Jump to content
SAU Community

Recommended Posts

Hello

I will either tune my rb20 det to 400hp with supporting mods, or buy a rb25 det and tune it to 500hp or maybe even a 26 and tune to 500hp.

I have 17" 225/40 wheels/tires on the front. Want to change to 17" 235/40.

17" 245/45 wheels/tires on the back. Want to change to 255/40 if can fit.

I am going to get the Nismo 2 way LSD. I have HKS coil overs.

My hicas works fine.

Is there anything else I can do to make sure I am getting power to the ground?

I dont want to go sideways unless I want too, and what to make sure I can handle curves, take offs, and driving well since I have rwd car.

Link to comment
https://www.sau.com.au/forums/topic/464755-getting-power-to-ground-questions/
Share on other sites

HICAS has nothing to do with it. Delete it and things will actually be better anyway.

Use the same size tyres all around. No sense at all in staggered fitment on an R32. 235/45-17 on 8" rims with +35 offset works well. 245s will also fit, but will bag a bit on 8s. 255s you're definitely talking 8.5-9" rims and then it becomes harder to fit everything under the guards without unwanted scraping or rolling. Look at the wheel sizes thread in Suspension, braking and tyres for guidance about what fits.

But more important than the width of the tyres is the tyre itself. It is better to use a narrower tyre with sticky compound and good construction than to use a wider cheap nasty tyre.

Alignment and bush condition are two very important things not to neglect. You can have $10000 Ohlins coilovers on your car and it still will not hook up properly if the rest of the suspension is flailing around because it's f**ked. Similarly, stacks of rear negative camber will not help (forward) traction at all.

Keep in mind something important. 400 engine HP on a Skyline is not much power really, but on an RB20 it tends to mean you have no torque followed by no torque followed by no torque then it comes on boost you make 400HP worth of torque and it breaks traction. There is little you can do to make that work. RB25s come onto boost more gracefully (at the same power levels) and feel much faster, simply because they have more torque and start making vehicle speed before they come on boost. But add another 100HP and you're still going to be able to break traction freely.

  • Like 1

HICAS has nothing to do with it. Delete it and things will actually be better anyway.

Use the same size tyres all around. No sense at all in staggered fitment on an R32. 235/45-17 on 8" rims with +35 offset works well. 245s will also fit, but will bag a bit on 8s. 255s you're definitely talking 8.5-9" rims and then it becomes harder to fit everything under the guards without unwanted scraping or rolling. Look at the wheel sizes thread in Suspension, braking and tyres for guidance about what fits.

But more important than the width of the tyres is the tyre itself. It is better to use a narrower tyre with sticky compound and good construction than to use a wider cheap nasty tyre.

Alignment and bush condition are two very important things not to neglect. You can have $10000 Ohlins coilovers on your car and it still will not hook up properly if the rest of the suspension is flailing around because it's f**ked. Similarly, stacks of rear negative camber will not help (forward) traction at all.

Keep in mind something important. 400 engine HP on a Skyline is not much power really, but on an RB20 it tends to mean you have no torque followed by no torque followed by no torque then it comes on boost you make 400HP worth of torque and it breaks traction. There is little you can do to make that work. RB25s come onto boost more gracefully (at the same power levels) and feel much faster, simply because they have more torque and start making vehicle speed before they come on boost. But add another 100HP and you're still going to be able to break traction freely.

I use Federal 595ss on the front and have some Pirelli's Cinturato P-7's on the back. THe Federals are pretty good and the Pirellis not too bad, good gripe.

I will probably go with all Federals when its time to change tires. The newer ones of course since the 595ss are discontinued.

I don't mind rolling the inner fender to make the tires to fit.

Don't install a 2 way, buy better tires

Don't worry too much about bigger rims and buy better tires

Don't lower the car more than a couple of inches... and buy better tires

once you have better tires, put better coil overs in it.

....

J.

Don't install a 2 way, buy better tires

Don't worry too much about bigger rims and buy better tires

Don't lower the car more than a couple of inches... and buy better tires

once you have better tires, put better coil overs in it.

....

J.

I understand buying better tires,

but why no 2 way? Whats wrong with HKS? Not sure how much car is lowered. I haven't messed with the height, the car is still the way it was when I got it. Already had the HKS Hyper D's on them. Its lowered some but not too much. Came that way.

I know about the big brand tires, Dunlop, Yokohama's, etc but I am in Japan and they charge a premium for the really really good tires from those companies.

From my experience the Federal's are good. Any model tire that is good that you can suggest?

Don't want to use semi slicks for everyday driving because its rainy season now and I don't want to wreck.

Federal 595 SS are rubbish.

You're in Japan, get Advan Neova tyres, should be cheap as chips for you.

A 1/1.5/2 way mechanical diff will help put the power down, your stock viscous rubbish will end up splitting the torque 90/10 instead of 50/50 like a mechanical diff

Oh, no KU36 please, they aren't a great option.

I really like my new Bridgestone RE002/003's, great wet performance even in torrential downpours when you would normally be aquaplaning like mad.

I wouldnt recommend AD08R's unless you can put some decent heat into them, great for track but not always great on the roads if you want lots of grip all the time.

RE002's were a good soft compound for me and also really love the Advan Sport V105 as a street tyre.

horses for courses really.

I wouldnt recommend AD08R's unless you can put some decent heat into them, great for track but not always great on the roads if you want lots of grip all the time.

That's actually one of the things I like about them. Get them warmed up on a spirited drive and they stick nice. Drive around familiar streets at home and you can skid them a bit without wearing them out!

We removed our AD08's off the front of one of our cars and put the new Federal RS-RR (extra R).

Cant believe the grip levels now.....wont be going back to AD08's in a hurry.....

We removed our AD08's off the front of one of our cars and put the new Federal RS-RR (extra R).

Cant believe the grip levels now.....wont be going back to AD08's in a hurry.....

how old were the ad08's? what were they used for until you changed them?

at half the price, the RS-RR's seem to be a clear winner.

Car is a Supercharged S2000 (1200kg) laying 250Kw at the rears.

Traction was great with AD08's In summer or with hard driving on windy roads, but all other times you needed to work them to heat them on the street, other wise, slide city.

RS-RR.....think AD08's when hot.....but its cold and you have not heated them yet....

Currently the RSRR are only on the front, now its point and shoot like a go kart, sticks like anything...the rears (ad08 still on) just follows the front while sliding.

also AD08s will die pretty quick after many heat cycles... same goes for Z221

I find if it's a street driven car, best to stick to the likes of Nitto NT05, RE002, Toyo R1R, etc...

  • Like 1

Our AD08's always needed some heat even when new.

Id agree that too many heat cycles dont do them any good and they fall off with mileage.

Will be interesting to see what the RS-RR's are like when old, at the moment they are outperforming the AD08's new for new.

Would be a perfect street car hill climb tyre, sticky with little heat.....will also monitor wear rate on them.....

Time will tell.

Went for some high speed late hard braking today, rear started to controlably slide sideways without locking when braking in a straight line, fronts were planted.

AD08's are on the rear.....they are at the point where i would call them dangerous when cold. (and heat cycled a few times too many)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
    • Literally looks like direct port nitrous haha
    • They are in fact just nozzles. They are there only to produce a spray pattern and limit flow. The injector itself is what I use to control flow to the 7x nozzles. My old system had no injector and only PWM the pump. This lead to a lot of inconsistencies, and poor atomization at low pressure when the pump was ramping up. 
×
×
  • Create New...