Jump to content
SAU Community

Recommended Posts

I have a r33gtst that is booked for a tune tomorrow.

I have all the supporting mods like r34 highflow, power fc etc.

My goal is about 240 atw

I bought a 1000cc topfeed xspurt injector kit from scottynm35 and even though i assumed they were too big, i was told that they are a much more modern design, can flow well at all power levels and therefore would be suitable for my application.

however the tuner tells me they are way too big and will not be suitable for my goals, he told me he can safely run the stock injectors by upping the fuel pressure with my aftermarket fuel reg.

What do you guys think?

Thanks

Link to comment
https://www.sau.com.au/forums/topic/466010-1000cc-injector-question/
Share on other sites

Strictly speaking, they are too large.  You'll only need ~1ms pulse width to idle on petrol and you therefore have very little ability to tune the idle mixtures.  But it will work.  Idle may be slightly fluffy, or it could be perfect.

On E85 it would be easier.

But what you were told by others than your tuner is true.  They will work, and they will allow you to go E85 later very easily.

I shudder in horror at the thought of jacking up the fuel pressure to achieve 240 rwkW on factory injectors.

  • Like 1

Run the 1000ccs, technology has already advanced so far over the last 10 years, they'll be fine
Upping fuel pressure with stock injectors will only lift the headroom by so much over the 200rwkw, works fine but stresses your fuel pump and affects injector lag time anyway

My main concern is, will the car run perfectly on the 1000cc injectors? i dont want it to not idle well or run just "fine".
I will speak to the tuner later today about it, but its looking like i will just cancel and wait a bit longer.
it definitely did not seem right to just up the fuel pressure on the stock injectors. The thing is the tuner is very reputable among the skyline and silvia community and i have heard nothing but good things about him.

If your tuner is smart, and say in the event those milled X-Spurts (I don't have experience tuning them) don't idle well on 98RON, you can drop the fuel pressure to say 2.5bar with the vac hose off on idle (then connect it back once you've finished setting the FPR).

This means now you can run higher pulsewidths and have the correct amount of fuel injected to maintain the idle and AFR of your choosing and you have plenty of headroom for the future.

I've got 1000cc IDs....no issues on idle.  I'm pretty sure there about about 1,000 others on here who'll tell you the same.

Keep the IDs, get a new tuner.

1 hour ago, vxsr33 said:

Called up chequered tuning and they said it would be no problem, so going for a tune with them. :-)

i was told the new injectors dont have filters though. Does anyone know where i can get some? (Dont know much about injectors)

Very good plan :)

 

Trent is good, he will sort it out. Seen several maps most of which are very good.

Seen big tuning shops in Sydney with tunes that could be done by a 2 year old holding the number 8 key. 

  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...