Jump to content
SAU Community

Recommended Posts

Sounds like the one I saw on facebook recently .. You can always get a Japanese history check done on it which should give you the auction sheet and de-reg papers. Also you could have the car inspected and comp tested for your piece of mind and atleast with the car being in the country you can check it out and drive it for yourself rather then dropping 70+ on something you haven't even seen. If the K's come back legit and it isn't a poor grade car then doesn't seem too bad a deal. Although it seemed to have a different number plate in every photo which looked abit dodgy haha.

  • Like 1
  • 2 weeks later...

Checked out Sparkling Silver R34 GTR in Vic on Carsales on w/e. Nice, pretty clean car except a bit of minor rust around radiator & engine clips & changed rear pods from silver to black & boot alignment slightly out so MAY have previous accident history???. Though main deciding factor not to buy was the last minute price jump from owner-eg we agreed on price on phone then 15 min before we met he changed price(higher)! Who does that?!

  • Like 1
  • 2 weeks later...
  • 2 weeks later...

Still looking gazz1991[emoji53]. Might be checking out bsb vspec this w/e in Melbourne by guy who sent me pm. Sounds & looks good(on photos & paper as has all papers from Japan grade 3.5/b). See how we go. Also still checking Japan Auctions

Ps. If I buy bsb this w/e might just need new bumper & new front diffuser. I can source front diffuser but does any one know where I could find genuine S Tune front bumper(not Z tune as V spec Performance has those in)???

It's not that anything is wrong with current bumper, just has that oil cooler side vent that I'm not a big fan of. Thanks in advance

Well if you cant find a GTR i can sell you my GTT the car is stock original except for mags and stereo head unit and with the rest of your money put into the engine you would have a nice fast car,this car is in very good condition.

Well if you cant find a GTR i can sell you my GTT the car is stock original except for mags and stereo head unit and with the rest of your money put into the engine you would have a nice fast car,this car is in very good condition.

Thanks Gazz1991, but I have my heart set on gtr(Rb26 R34).
  • 2 weeks later...

Excited, as I 99% will be buying & picking up Bayside Blue R34 GTR V Spec tomorrow!! Met fellow SAU member, top guy & has been very honest & helpful through whole process. Let you guys know how I go.

  • Like 3
Excited, as I 99% will be buying & picking up Bayside Blue R34 GTR V Spec tomorrow!! Met fellow SAU member, top guy & has been very honest & helpful through whole process. Let you guys know how I go.

WAHOOOOO good luck dude!

Finally got my new baby!!! I'm now a proud owner of a bayside blue R34 GTR V Spec[emoji1]. Low k's, good condition & sounds & pulls like a dream at 306kw-(thanks a lot to Milan for his time, money & effort put in car). Milan was awesome with helping organise process & helped make my Xmas & year by eventually agreeing to sell me his pride & joy-I promise to look after her mate. After loosing my dad & best mate this year, was hard to be happy......but now that I've truly experienced(& own) my dream car, I can honestly say I'm optimistic & truly happy again! I now believe Passion can overcome misery, and GTR overcomes all haha[emoji23][emoji23][emoji23][emoji1419][emoji1419]

  • Like 8

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...