Jump to content
SAU Community

Recommended Posts

M35 DIY turbo replacement

Hi all, 

Apologies for creating a new thread but I can't for the life of me find any DIY threads for replacing a blown turbo on the VQ25.

Funnily enough the threads I have found refer OP to the search function. 

I understand a few owners have had to go through this heartache but has anyone documented it for use on this forum?

Keen to grab an M35 and want to research turbo replacement as it's going to need it sometime down the track but sale depends mostly on ease of replacing this critical part.

Link to comment
https://www.sau.com.au/forums/topic/468871-m35-diy-turbo-replacement/
Share on other sites

Here is a swap I did over 5 years ago.

https://www.sau.com.au/forums/topic/352166-m35-engine-and-turbo-out/

Its a fun job that I personally would only do once so never again. 

Some owners love swapping there turbos out.

  • Like 1
  • 3 weeks later...

Have just been unfortunate enough to have replaced the turbo on my M35. It is definitely diy able but by no means an easy job. Patience is the key. What makes it difficult, is the lack of access to the dump pipe/t3 flange bolts. The bolts are more than likely rusty and fused on. Each bolt takes quite a while to remove because of this.

You will need a jack, stands/ramps or hoist, wd40, inox or penetrine etc to spray the bolts with and let soak overnight (i used chemsearch yield) worked brilliantly. A range of extensions, uni swivels for your ratchet, long spanners, shorty spanners, an obstruction style 14mm spanner helps with dump pipe bolts as well, a 22mm spanner for the 02 sensor. A couple of brake line clamps to clamp the coolant feeds so you don't have to dump the coolant. You may have to make or bend a spanner to remove one of the heat shield bolts or smash it off. You will need to remove the front pipe, brackets, disconnect the gear shifter and then unbolt the gearbox cross member and lower transmission to give you access to dump pipe bolts. If you've removed turbos before you will eventually get there, if you haven't, it's not the car to learn on. Just pay someone else to do it and save yourself the headaches.

lol......after doing about 30 of these I can tell you its a different experience everytime. I think the fastest I ever did one was 5hrs......the slowest was about 18hrs. You could never guess which one was to make you its little b@#ch.....the only thing that was always consistent were the little cuts all over your hands and arms. I ended up with 2 draws of my toolbox that was specific to the NM35 turbo change.

 

Glad you had fun....and I'm glad I will never touch another NM35 for the rest of my life!

19 minutes ago, Jetwreck said:

lol......after doing about 30 of these I can tell you its a different experience everytime. I think the fastest I ever did one was 5hrs......the slowest was about 18hrs. You could never guess which one was to make you its little b@#ch.....the only thing that was always consistent were the little cuts all over your hands and arms. I ended up with 2 draws of my toolbox that was specific to the NM35 turbo change.

 

Glad you had fun....and I'm glad I will never touch another NM35 for the rest of my life!

Bullshit you still owe me a turbo change :P

lol......after doing about 30 of these I can tell you its a different experience everytime. I think the fastest I ever did one was 5hrs......the slowest was about 18hrs. You could never guess which one was to make you its little b@#ch.....the only thing that was always consistent were the little cuts all over your hands and arms. I ended up with 2 draws of my toolbox that was specific to the NM35 turbo change.

 

Glad you had fun....and I'm glad I will never touch another NM35 for the rest of my life!

Lol, sounds like fond memories. I wouldn't touch another one either unless it's mine. Believe it or not, no cuts on my hands but elbows took a beating. Definitely the shittest job I've ever done on a car, actually timing belt and supplementary auxiliary drive system on an import diesel Toyota estima was almost just as bad.

 

P.s I put a used stock turbo in it, may need to be done again soon. I'll bring it over to you[emoji1]

 

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • Bunnings would have just handed you your money back on that one!
    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...