Jump to content
SAU Community

Recommended Posts

Transport Costs for R33 Skyline GT-R

Hey I am extremely new to these forums as I am a current BMW owner looking to buy my first import. It's a R33 Skyline GT-R Vspec. Just one problem, the one I am super keen on with low mileage and a pretty decent exterior is in WA and I am located in the ACT. Could anyone assist with their knowledge of how much it would cost to have that car hauled from WA to the ACT or maybe at least somewhere I can then drive it home from. Really unsure as to how this would be accomplished or if it is doable, seeing as WA to ACT is basically across the whole country. 

Help is much appreciated (:

Hello, I too got my car from WA and had it shipped to Victoria. My costs were $1800 door to door. My car went on the flat, enclosed race transporter rather than the open ramped style transporters. 

I used Ceva, as Glavsport in WA had experience with them and had no problems with them. It did go very well, however, just be cautious if you go with Ceva as a high number of other people had not had such great experiences. If I were going to ship another car, I would take careful notice of the condition of the panels and most importantly take a photo of the dash cluster before it leaves and compare it once you receive the car. If you do this, you'll be ok.

Best of luck. Steve.

(Edit: I should add that it ends up on a train at some point and I don't know too much about that, it might be enclosed, or possibly not, best to ask).

Edited by Steve85
  • 4 months later...

You can save a fair bit of money by going to the depot to pick up the car yourself and/or getting the seller to drop it off at the depot on their end.

Make sure that ride height clears 12-15cm, as some freight companies will not accept vehicles that are too low.

Horror story of transporting my 33R from Canberra to Melbourne - I flew in to purchase the car and had booked to fly back home later in the arvo. Long story short, the depot knocked back the car cause it was 10cm off the ground. So I was outside a mechanical workshop 1.5 hours before my flight was due to depart, painfully tapping coilovers with a hammer and screwdriver trying desperately to raise it, overinflating the tyres and eventually ripping off the front lip so that the car would clear 15cm and the depot would take it. I had to leave the lip at the workshop in Canberra cause I wasn't allowed to put any objects in the car for transport. Didn't know what they were worth at the time...lucky it was a slightly damaged one...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...