Jump to content
SAU Community

Recommended Posts

Self leveling light problem

Hi guys, 

I've tried to find something on the form but unfortunately I wasn't able to find someone with my problem.

Long story short, I'm not using a lot my car ,so most of the time is parked in the garage. Last time everything was working fine, few days ago I went for a ride and I noticed something wrong with the headlight. When I turned them on instead to leveling at the right position they went all the way down.

Actually I know there's somewhere in the back some sensor can automatically level the headlight, but unfortunately I have no idea where is and if the problem is relative to it.

Any help would be great.

Cheers

PS. The car is a CPV35 2006

PS2 sorry for my bad English.

 

Edited by Loris_V35
Link to comment
https://www.sau.com.au/forums/topic/470369-self-leveling-headlight-problem/
Share on other sites

Does it have a headlight height switch? If not, then check these
http://jp-carparts.com/nissan/partlist.php?maker=nissan&type=152&cartype=13&fig=253&page=15

https://partsouq.com/en/catalog/genuine/unit?c=Nissan&ssd=%24HQARW1d0BAsGAwIVOjlKShl3bWlsbD8OMBM%24&vid=19574&cid=4&uid=558440&q=

Strange that both drop, possible the height controller box died. You should be able to disconnect the motors on the headlights if so.

3 hours ago, niZmO_Man said:

Does it have a headlight height switch? If not, then check these
http://jp-carparts.com/nissan/partlist.php?maker=nissan&type=152&cartype=13&fig=253&page=15

https://partsouq.com/en/catalog/genuine/unit?c=Nissan&ssd=%24HQARW1d0BAsGAwIVOjlKShl3bWlsbD8OMBM%24&vid=19574&cid=4&uid=558440&q=

Strange that both drop, possible the height controller box died. You should be able to disconnect the motors on the headlights if so.

Thanks mate, I think I have found the part.5911885d5b5fc_IMG_20170509_1755341.thumb.jpg.72d54eec8d1f6426616cc00303748514.jpg

I tried to disconnect it and move it manually, but the headlights weren't moving.

591187a438eb1_IMG_20170509_1756041.thumb.jpg.9c858b15e4d86738bbb8e19350aea434.jpg

I tried to disconnect the plug with the lights off, and when I turned the lights on, the motors didn't turn on and didn't lower the lights.  When I put the plug, back in, the motors lowered the lights down.

What do you think? Thanks for any suggestions or advice!

I'd need to get a look at a schematic to understand what's going on but I'd imagine there's a sensor, control circuit and a stepper motor. One of those three components will have failed. If it's an optical sensor, it might just need a clean with isopropyl alcohol. If it's a mechanical sensor, it'll either need a clean or replacement. If it's the control circuit, easiest approach would be to replace it but if it's just a dried out or shorted capacitor, that can probably be cheaply sorted out. If it's the stepper motor, you can determine that by feeding the appropriate pins with 12V to see if you get any movement out of it.

Again, without a schematic, hard to be sure where to begin with the diagnosis past the obvious mechanical bits.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm actually not sure - I think it was "Stealth Performance" (It really is near impossible to find a FEMALE 1/8BSPT to 1/8NPT male at ALL) but having the thing leveraged on a 90 degree angle on a small aluminium fitting is not too smart. Also in not too smart, I've drilled out the center of the broken fitting so there's maybe 0.00001mm of thread to bite into, so yeah. I may have to get it drilled/tapped/plugged entirely. Given I could conceivably tap a thread/adapter/pressure line in any point in the oil system I suppose it's feasible to run a line to the Nissan Sensor to keep the dash working. Do these exist in AN fittings and the like? Like an AN fitting that has a NPT (or other?) thread as well for putting a sensor in?
    • I would agree.  There will be an amount of boost you could run safely with an otherwise factory system, but it would be low enough to not be worth the cost.  And if you are reliving your 20s, you know a 'little bit' was never enough. Personally, if I didn't want to spend the money, then stick with NA bolt-ons, and maybe a tune.
    • Fuark, at least the motor survived. What brand was the fitting that snapped?
    • Wrong question. There's no point in spending the rather large sum of cash and effort to add turbo, without taking it to the "sensible" limit of the motor itself. If you have to upgrade injectors, etc, then so be it. That is a tiny fraction of what it will cost you to turbo it.
    • Measure voltage at the starter solenoid terminal when the key is at start and it has clicked. If it is really low, then the suspicion falls on the ignition switch (contacts or wiring thereof) as causing a voltage drop instead of sending enough volts to throw the solenoid all the way to engage the starter itself. If it is a decent voltage, then the suspicion is on the solenoid. Might have s horted coil, or might hva dirty contacts. Rip the starter off, dismantle, clean up contacts and inspect winding. It might not be possible to see if there is a short in the winding though. I have a spare starter here that I could measure the resistance of the coil, as a guide to about what it should be, if you need a comparison. <parts hoarder>No you cannot have it.</parts hoarder>
×
×
  • Create New...