Jump to content
SAU Community

Recommended Posts

Light throttle jerking issues

Hey guys, had my RB3025 neo tuned and runs great except for on very light throttle where it starts jerking.  I've had the tuner look at the low load points and says the pwr fc is old model and most likely the problem.  I'm gonna have a road tune done also to try find out more but can anyone suggest anything else that can cause jerking.

So some stairs of setup

2530neo, 3076, 44mm tial, z32 on 4inch pipe, gfb recirc BOV set soft, pwr fc, avcr, 1000cc experts, 416 walbro, stock reg, 

One thought was I had to weld up the r33 throttle vacuum hole as it wasn't compatible with the neo mani.. not sure how important that is..

Link to comment
https://www.sau.com.au/forums/topic/471448-light-throttle-jerking-issues/
Share on other sites

  • 2 weeks later...

It's called "ACCELER." and the screen looks like this.. unfortunately it's upside down (got it off Google).

You will need a wideband and see what the AFR is like when you jab the throttle vs. RPM. Of course too rich will stumble, too lean will stumble.

Column 1 = RPM
Column 2 = how much fuel in ms
Column 3 = how long in ms

Because you're running larger injectors than stock, I would say reduce the amount in column 2 by the percentage of your injector size increase.

So OEM is 370cc right? now you have 1000cc or so.. that means you would only need 37% of the original throttle pump values.

Play around with it, however you will need a wideband.

 

images.jpg

  • Like 2

My MR2 turbo does this. When on light throttle it misfires. 

I replaced just about all of the vacuum pipes. It's much better now but still not 100%. I still have the replace one pipe that comes into the cabin. Hopefully that sorts it.

  • 3 months later...
1 hour ago, Trex said:

Did you find a resolution to this? @AngryRB 

The tuner had it a week for cold start and cruise adjustments and has improved alot, said it was running quite rich and needed new plugs.  It seems to go jerky after a bit of a flogging and not so much when normal driven.. Ive been told its likely the power fc and the injectors being so big. Be interesting to put a haltech in but cant justify the coin.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...