Jump to content
SAU Community

Recommended Posts

Need advice on choosing manifold - rb26/30 single turbo GTX4202R

Hi all

I'm currently in the process of dummying up the fitment of my garrett GTX4202R on my rb26/30 and of course running into some fitment issues.

1) First issue is the clearance between the turbo and the block - the compressor housing fouls against the rocker cover by maybe 1-2 mm. Might be able to either relieve the rocker cover or offset grind the cylinder head flange by 1mm or so to angle it out slightly. EDIT: or does anyone make an exhaust manifold insulator/spacer? even 3-5 mm would probably do it.

2) second issue is more difficult. the manifold seems to sit the (admittedly huge) turbo too high in the bay to shut the bonnet. This is probably not assisted by the fact that I already have an extra 38mm of deck height due to running the rb30 block.  But it's so close I won't really know until I dummy it up.

It's a nicely designed mx motorsports steampipe manifold with a nice collector and having done some measurements with a spare block, it's going to be a game of millimeters. But just want to know if there are any manifolds which sit the turbo nice and low in the engine bay, while still clearing the a/c - I would prefer to just buy something ready made and minimise the amount of screwing around if possible, in the event it comes to having to buy a new manifold.

any suggestions gratefully appreciated. Oh, needs to be twin-scroll T4 flange, and if possible twin 38mm v-band gates.  Or, custom. Some that I've seen also angle the turbo out sightly so the intake is looking more to the passenger-side headlight.

Cheers

Andrew

Edited by dorifticon

Goodluck with it, I'll be dummy fitting my 68/70, hopefully in the next couple of days. I measured what I can and I'm in the same boat as you, I think it's going to be a game of mm! Mines a 26/30 as well so always fighting for mm when it comes to under bonnet clearance lol

6 boost make a 26/30 specific manifold that clears everything and has good clearance for bigger turbos. I am running one of their manifolds in twinscroll t4 albiet with a single 60mm gate just to help with space however the 6870 clears no worries. Motor is a 3.2 sitting on standard mounts with crossmember in standard position.

18738796_1686579274702768_8125430541312686809_o.jpg

what type of mods are we talking - removing sections of the bonnet ribbing or something more serious?

 

Also what wastegate setup- single or twin? retaining A/C? 

 

Finally, - what brand is the manifold?

  • 3 weeks later...

Hi dorifticon, manifold is a custom job for a guy who works out of the JEM workshop.

I'm running a single precession wastegate that came with the turbo .

Bonnet mods, just needs a small section of the ribbing removed. The bonnet actually closes but is raised about 5mm on the turbo side, obviously from hitting the turbo, the ribbing is about 30mm at that point and hits the cold side of the turbo so once cut should be all good. I've also had the manifold and turbo ceramic coated to help deal with the heat

 

I had the same issue

ordered a "gt42" 6 boost manifold for my r32 gtr 2.8 stroker and my 7175 didn't clear by miles

got sent another one which didn't clear either

ended up buying a custom made turbo1 manifold with twin external 38mm wastegates

turbo sits perfect now between turbo and bonnet, turbo and strut tower and most importantly clears AC lines 

IMG_2409.JPG.9de493b52fdf6c8f041c479fc1abeed3.JPG

IMG_2319.thumb.JPG.2f7c93bbbe35e6fe43fedde71d8bc4ed.JPG

Oh yes that was the other part of the question, yes I have AC and it cleared the lines by a mile.
Didn't quite clear the bonnet but it was made for an r34 with an rb26 not a 32 with a 30/26.
And since the bonnet has already been slightly modded for engine clearance I'm not fussed in cutting it a little more

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...