Jump to content
SAU Community

Recommended Posts

Hi my r34 gtr always run lower oil temp since i import it 2 years ago. and now even lower with some addition mods like nismo thermostat, and big oil sump etc. 

At moment it run max 75C(normally around 60c-70c depend outside temp) oil and 70C water on street. if i push it hard for 10 mins the oil temp still around 90c, water temp below 80c.

the car has nitto oil pump, high octane 9L sump, nismo oil cooler.  arc intercooler, nismo radiator. car is running e85 made near 500awkw.

should i worry about the oil temp?  i'm start thinking i got bad sensor:(

If you're running 10-40/50 synth oil, perfect operating temp is around 90 deg as far as i'm aware. 

I'm running a Tridon 71 deg thermo i think. Sits on 80-83 deg in normal traffic and cruising.

You can tune around the lower temp using fuel/temp corrections, but 70-75 seems a bit too cold for these engines????

 

i'm not really worry about the water temp, but the oil temp look too low for me. the oil temp only go up to 80C+ when in really bad traffic like 10 mins drive 1km. i use 10w40 or 5w40 oil. maybe i should change to 5w30?

21 hours ago, GTSBoy said:

Oil and water in contact in the HX.  Warmer water = warmer oil too.

yes true. but even before i put the nismo thermostat the oil temp still that low.  with the nismo thermostat only the water temp goes lower which is normal for low temp thermostat.  i did a short drive today, found the oil temp did go up to 75c in city with a lot stops. water temp is around 70c if i cruising around , but it go up to 85c when stuck in traffic.

Get rid of the Nismo thermostat and replace with stock. Get a thermostat for your oil cooler and/or make a cover for the oil cooler when you are not thrashing the car. (maybe you are not pushing it hard enough!).

17 hours ago, KiwiRS4T said:

Get rid of the Nismo thermostat and replace with stock. Get a thermostat for your oil cooler and/or make a cover for the oil cooler when you are not thrashing the car. (maybe you are not pushing it hard enough!).

You are right. I did not pushing it hard enough:) but Is there any long term effect from the lower temp? The car drive perfectly. Power always there.   And I change oil every 3000kms or sooner. 

17 hours ago, KiwiRS4T said:

Get rid of the Nismo thermostat and replace with stock. Get a thermostat for your oil cooler and/or make a cover for the oil cooler when you are not thrashing the car. (maybe you are not pushing it hard enough!).

I think Nismo oil cooler should include the oil thermostat plate?

3 hours ago, GTSBoy said:

Yes, running engines too cold increases wear, and fuel consumption (assuming tune is not adjusted to suit).

thanks for reply.  i will try use some cardboard block the oil cooler and see the different. my tune is suit for low temp no problem.

  • 2 weeks later...

I recently installed oil cooler and gauges in my car.  I actually didn't think too much about the oil temp being too cold.

 

My gauge starts at 50.  I warm it up, then baby it, revving to 2500 until the gauge starts to move, but it never really gets more than 60 driving.  Running it hard through the hills it might maybe go to 70 and on the racetrack will go to 70-80 max.

I am running 15-60w penrite/nulon.  Should i be concerned or do anything ? The cardboard idea was good...

 

Greddy oil cooler located drivers side

 

 

080120161431.jpg

080120161433.jpg

080120161434.jpg

080120161435.jpg

080120161436.jpg

080120161437.jpg

It's not the 10 in 10-40 that you should consider changing down.  It's the 40.  The smaller number is the "winter" viscosity, which essentially how it behaves dead cold.  At 70 ish degrees, you're not talking about that end of the oil's rating, your talking about the normal end.  So if you're running 40 now, then 30 would be the logical decrease, if you were going to try to deal with your possible low-oil-temperature-causing-high-viscosity problem by running thinner oil, that is.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...