Jump to content
SAU Community

Recommended Posts

Hi guys, this has been covered only a hand full of times as far as I can see and none have definitive answers on actual lengths, only the theory behind changing traction arm length. 

So, today Christian and I from Sideways motorsport in Brisbane tested a number of different traction arm lengths in a r34 gtt and measured toe through from full droop to full compression to measure bump steer (toe changes with changes in bump).

Firstly, we removed the rear coilover, and removed the wheel.

Christian then made a little jig to fit to the hub of the vehicle out of stainless plate that we bolted on to the hub using the wheel nuts, then setup a string line parallel with the hub and took a measurement of the distance from the string line to the hub from the front and back of the stainless jig / plate. 

We then jacked the hub up to full compression and measured the change in distance from the front and rear of the plate. We then had the measurement in mm for the toe change through the wheel travel. We tried a number of different traction arm lengths, from fuly extended to as short as possible. The least amount of toe change we found was with the traction arm set to 7mm longer than standard from centre of bolt hole to centre of bolt hole. The ride height is around 330mm and camber -2 in the rear. 

My question is what lengths have other people tested and found that a certain length minmises bump, im asking because the jig we made is relatively crude and my guess is a little bit of human error would certainly be involved in the measurement process. 

Any insights on this matter are most welcome !!

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/474495-traction-arm-length-for-bump-steer/
Share on other sites

Everyone else's traction arm length will be specific to;

  1. Which car - R32 different to R33/4, etc,
  2. Upper control arm length,
  3. Static toe setting.

So there's no point in trying to compare too many apples with oranges.

You have likely found a setting which is far better than what you had before.  If your jig is a bit rough, then maybe it's not the best setting possible, but still better.

If you want to consider an alternative way of doing it, strap a mirror onto the hub or disc face.  Place a board upright, parallel to the car about 2-3m out from the side of the car.  Clip some paper onto the board.  Shoot a laser point at the mirror from a spot close to the edge of the board/paper so that it reflects onto the paper.  Keep the total angle as small as you can.  Jack the hub up and down and mark the reflection points on the paper.  You will get a line that goes up and down as the hub swings through its arc.  Any forward/backward motion of the reflected dot is bump steer.  You can change the arm length and generate another curve on the same piece of paper.  Do this and get worse bump steer?  Make the opposite change.  Then just increase or decrease arm length until the line is as close to vertical as possible.  It has the beauty of not needing to work in the same place to adjust the arm as your jig/dial gauge/whatever measurements are being taken.  It's less quantitative as to how big the toe change is in mm unless you measure the change on the paper and do some trig to work out the swing at the wheel, but that hardly matters, because all we're looking for is the smallest amount of bump steer.

  • Like 1
  • Thanks 1

Hi Gts boy, thanks for your feedback, ok I can understand why the upper control arm length and different cars are going to affect the relationship with the traction arm, but why does the static toe influence toe under bump ? I guess my thinking is setting static toe doesnt really affect toe under bump, thats the traction rods job, whether you set you toe at 2mm out or 2mm in for the rear, doesnt it just matter than its not changing under bump ? Or am I looking at this the wrong way ? 

Yep ok thats another neat method of measuring toe change, as you say and Carroll smith says in his books, we dont care how much bump steer we have quantitatively, only that we eliminate it !! 

Edited by Ben26

The static toe is set by the tie rod length (or toe control arm with no HICAS), which, for the purposes of the geometry of the swinging of the wheel, is a 3rd link (actually a 4h link) that swings through a different arc than the lower control arm that it runs near.  Different locations for the inner and out ends.  Causes a small tweak to the path of the other arms.

Ah ok, yep Im aware that you change toe using the tie rod but to me it looked as if adjusting that arm had little to no effect on the traction arm or upper camber arm. I will remember that for next time, thanks for your advice

OP are you using stock upper control/camber arms or adjustable? i think an exact length isn't commonly posted because as GTSboy says, it's relevant to the individual setup. It's prob 2 years back since i did mine - numbers are written down somewhere in the garage but to quote numbers through a foggy haze of memory, i think i measured my traction rod at 218mm stock length bolt to bolt, and ended up at maybe 223mm? 

The point was though, the 'best' length in my testing, was changing it by the same ratio as you change the camber arm to reduce camber once the vehicle is lowered (my rear camber is -1.75 deg). I would imagine Nissan spent a fair amount of time to minimize bump steer when calculating the suspension geometry so it would be no surprise that maintaining the same relative lengths on the arms would give the best results, to approximately maintain Nissan's geometry.

Hi Andy I have adjustable camber arms as well, so I set the camber roughly where I wanted it to be to begin with, then started playing around with the traction arm length. I measured my stock ones at 210mm middle of bolt hole to middle, and I ended up with a traction arm length of 217mm so it seems we have a similar result. Yea Im aware that the combination of the two upper arms has an effect on the toe curve of the rear suspension, But I was just trying to get a ball park figure of what people were getting. 

Yea that makes sense, so you think that if you get a ratio between the length of the standard traction arm and camber arm, and maintain that ratio, you would achieve a good result. I might have to test that, sounds like it might be a good starting point for future cars / set ups. 

Thanks for your insight my friend.

Edited by Ben26

If you are doing this type of thing on a regular basis I'd suggest that you invest in a couple of dial indicators and make a jig like this, it will give you the most accurate and repeatable results. Cheap dial indicators are available for as little as $35 these days so for a total investment of ~$100 and a couple of hours you will be able to create a measurement device that you will doubtless use on countless occasions in ctrp_1001_07_z+bump_steer_explained+whee future.

 

Ah yes I have also found decent bump steer measuring devices online for a few hundred dollars so I think for next time I will certainly either build a better jig with dial indicators or purchase an already made rig. 

Yep, on my car I also measured them at 210mm and my length I set at 217mm, the sweet point for me was between 215mm and 217mm so it seems as if we are on the same page even if setups are a little different. Thanks again gts boy. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...