Jump to content
SAU Community

Recommended Posts

I have a few issues with my car at the moment:

Pretty bad shuddering in reverse with wheels turned (fine when reversing in a straight line)

Shuddering when driving in a straight line- almost feels like the car is rhythmically binding up a bit. Worse with power on, but still happens when rolling in neutral.

Really really bad shudder on moderate and hard acceleration. Goes alright but it's quite nasty- almost verging on quite a harsh vibration/shudder/clicking noise/feeling. At first I thought it was a terrible misfire/boost cut but I'm fairly sure it's a mechanical drivetrain issue.

The engine is running well so it's not misfiring. All new coils, O2 sensor, MAF, exhaust, CV's all checked and good (one replaced). Wheel bearings all good. New gearbox fluid, need to flush attesa fluid and transfer case. I've got 370Z staggered rims but was doing this with the standard ARX rims as well.

The attesa pump appears to be working properly, no 4wd light on dash.

With an upgraded ecu with tweaked shifts it was doing some really nasty gearchange bangs (particularly on downshift at 100k's and some gearchanges at low speed), alleviated by Christian kindly sending me a re-programmed ecu without gearshift changes.

I've got heaps of troubleshooting to do, was just wondering if anyone else has come across the same symptoms?

Link to comment
https://www.sau.com.au/forums/topic/474761-m35-gearbox-or-attesa-issues/
Share on other sites

  • 2 weeks later...

Mini update. Took front propshaft/driveshaft off so it's RWD. Most the the problems are gone. The shaft itself has two stuffed universal joints which I hope to rebuild. In the process of ordering some suitable internal circlip joints from the USA. Rockford RCV 430-9, 0.791" cup, 1.285" circlip-circlip. I know, strange measurements for a metric Jap car... Did ask locally about getting the shaft rebuilt and they said they'd have to weld new yokes in (which might have clearance issues) and $850. $1450 from Nissan for a new replacement shaft and front diff flange (our shafts are discontinued and they only have later ones available with different flange on the end).  

Once that's done I'll put it back in and see what happens- oh and change transfer fluid as well.

Doesn't explain the funny gearchanges though.

Checked my tyres and they are all the same size (albeit on different width rims) so I don't think they are causing an issue.

Edited by andynogo
2 hours ago, KiwiRS4T said:

Driveshaft people should be able to fit universals - after all they can do it on cars with no circlips by machining existing yoke. Ask around for other driveshaft specialists.

They can but you can't find the right size uj's in Oz. They are available in the USA so I have two on their way from Rockford. The local guys want to weld new yokes on which are bigger so may not fit our cars. I guess they don't want to order the replacement joints in from the US... They also can charge a lot more for this.... Or am I being cynical? 

I have all the gear to get the old staked joints out and fit new ones. The trick is getting them centred and with the correct amount of lash- I have a lathe and dial gauge which makes this much easier. I'll also save over 700 bux which is handy.

Edited by andynogo

I'm actually going to do a rolling circumference test on the fronts and rears to see if there's any difference. Could always try to find another set of those wheels and use the 9's all round as the 8's sit way inboard at the front- using 20mm spacers to get them out a bit so 25mm/1" would be perfect I reckon.

  • 2 weeks later...

Replaced the front uni joint in the front propshaft. There's another story just in that- circlip grooves not machined correctly in the joint bearing caps. That took a while and lots of swearing to figure out. Can't replace the rear joint yet as I need another joint from the manufacturer as those bearing caps are just too far out.

Anyway so far under full acceleration I haven't noticed any of the previous problems. No surging, clicking, funny gearchanges etc. I did change the transfer box fluid as well which may have helped a bit. The only thing left to do now is check for high speed vibration which I'll get round to soon. Fingers crossed!

  • Like 1

Alright so replaced front discs so I can drive it again. Took it out on the freeway for a blast and....

Pretty bad shuddering in reverse with wheels turned (fine when reversing in a straight line) Fixed!

Shuddering when driving in a straight line- almost feels like the car is rhythmically binding up a bit. Worse with power on, but still happens when rolling in neutral. Fixed! This was pretty bad at all speeds but worse at 80-110. This is all good now.

Really really bad shudder on moderate and hard acceleration. Goes alright but it's quite nasty- almost verging on quite a harsh vibration/shudder/clicking noise/feeling. At first I thought it was a terrible misfire/boost cut but I'm fairly sure it's a mechanical drivetrain issue. Fixed!

I also had some pretty dodgy gearchanges especially 1-2 and 2-3 at lowish speed. This problem is gone now as well. Possibly related to front uni joint binding up.

So to recap, replaced the front uni in the front propshaft (old one was seized and had excessive play when freed up), bled attesa system and replaced fluid in the transfer case.

I had replaced the front right inner CV joint but that although a little worn wasn't causing any dramas.

This has fixed all the problems as described above. YAY!

  • Like 1
41 minutes ago, Skylinefreak1 said:

Excellent! Do you have part numbers or something for that front propshaft uni? Mine also has a vibration when the front wheels are also driving under hard acceleration.

Read the second post. :) but be prepared to get the cups machined as the circlip grooves might be way off...

http://motormasterpowersports.com/product/detail/sku/430-9/

 

Edited by andynogo
  • Like 1
  • 2 weeks later...
On 9/27/2018 at 12:50 PM, Skylinefreak1 said:

Excellent! Do you have part numbers or something for that front propshaft uni? Mine also has a vibration when the front wheels are also driving under hard acceleration.

Just one other thing- change all your attesa fluid- rear reservoir, line up to the back of the gearbox and the transfer case as well. Your vibration could be a transfer clutch issue. If it's not that then it'll be a uni joint in the front propshaft.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...