Jump to content
SAU Community

Lower Intake Manifold Removal

inmaniac

By inmaniac,
in General Maintenance

 Share

Recommended Posts

inmaniac Community Regular

inmaniac

Posted
Posted

Hey guys, hope you’re all good.

I have an obnoxious sounding vacuum leak somewhere under my throttle body. It’s very bad and throws out the car terribly, so it’s off the road and I’m addressing ASAP. There is no issue around the TB itself and I don’t see any kind of issue around the fuel rail or injector seats, so I’m assuming it may actually be either the upper plenum gasket, the lower inlet manifold gasket, or perhaps an idle control hose underneath the manifold somewhere. 

To the point of my thread - if I can not locate any obvious leak, I will be pulling off the intake to replace the gaskets. Should I get so far as to pulling off the lower intake, I was just wondering if anyone had tips or advice to share? Specifically regarding how and what to disconnect in regards to coolant hoses, vacuum hoses, etc, and if there are any tricks to any of the bolts?

Ive searched extensively on this topic but most threads only cover the upper plenum and I’m looking for any general helpful tips to removing the whole thing. So far my plan is to remove the TB, the fuel rail, then upper plenum - raise the front of the car up and just see what I can attack from the bottom. Assume that’s the best method?

 

Thanks in advance!

Link to comment
https://www.sau.com.au/forums/topic/474913-lower-intake-manifold-removal/
Share on other sites
BIG_FAT_MIKE Newbie

BIG_FAT_MIKE

Posted
Posted

If you're going to replace the upper plenum gasket then you should definitely do the bottom one to. The bottom plenum is actually really straight forward. You just have to fight the awkward angles to get the bottom bolts off. Legit just did this whole job in 2 hours the other week. Take a lot of pictures. It was actually really hard for me to mess up, so don't worry about that. I attacked everything from the top. Never once did I go under the car. And btw, my car was making a god awful whistle noise too. Turned out to be the gaskets. Let me know if I can send you any pictures or anything.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • GTSBoy
      R32 GTS (RB20DE) Injectors Replacement

      By GTSBoy · Posted

      No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • codygrimm27
      Can you mount the ATTESA pump in other locations?

      By codygrimm27 · Posted

      Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      You think its the AFM? I know its a common issues on R32s. I find it coincidental how this issue raised right after cleaning the fuel system. As everything except the fuel system was fine before. I tried running it with the IACV unplugged but did not notice a difference and still stalled. However, the RPM gauge is not in the cluster right now, so I will need to connect the laptop again and use Nistune to check the RPM. I will check this weekend.
×
×
  • Create New...