Jump to content
SAU Community

Recommended Posts

Hey guys - So I had issues with my gearbox coming out of 4th gear off throttle.

My mechanic looked at the joint from the shitter into the gearbox and we replaced it anyway but no change.  Then my tuner actually took it apart as he noticed the boot at the bottom of the shifter was gone so that made these quiet again and also stopped some fluid spilling over the top.  He also noticed that the shifter had some parts install wrong and fixed this (grrrr at my mechanic).

This fixed the 4th gear pop out issue but then I was driving along and off throttle again and 5th gear popped out which it has NEVER done.

Now im just confused as to why its changed from 4th to 5th with a correctly installed shifter.  Any ideas?

Link to comment
https://www.sau.com.au/forums/topic/475273-gearbox-trouble/
Share on other sites

Either an engine or gearbox mount is sufficiently stuffed to have had the whole driveline move such that the shift lever is getting pushed by the side of the tunnel hole, or, there is a problem with the selectors.  You might have lost a dowel or pin that holds the selector onto the shift rod.  Might be only partway out and wobbly.

I'm sure there are other possibilities too, but failing to imagine them right now.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/475273-gearbox-trouble/#findComment-7889712
Share on other sites

Has the gearbox ever been overhauled?

Many things could contribute to this, from worn bearings to worn synchros, etc.

Something simple, try flushing the box and popping in fresh fluid. If the box is pretty much on it's way out, then potentially use Redline Shookproof to mask up the problem and drive it till the box goes bang.

(That's what I'm doing).

Link to comment
https://www.sau.com.au/forums/topic/475273-gearbox-trouble/#findComment-7890163
Share on other sites

Yeh the box has been overhauled once before (5 years ago).  I was thinking of doing a fluid change but didnt think that will make a difference to it popping out of gear off boost.

I may have an opportunity to get a gearbox (no transferase or shifter which I dont need) for cheap.  Then when this one is out I can rebuild with stronger.

Link to comment
https://www.sau.com.au/forums/topic/475273-gearbox-trouble/#findComment-7890338
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...