Jump to content
SAU Community

Recommended Posts

I have a r33 gtst ( auto ) and it’s stock apart from a front mount intercooler, carback exhaust and pod filter. 

It runs fine up until 6psi but once it goes over 6psi the car cuts out and jolts foward ect . Can’t figure out if it’s a boost cut or fuel cut or why it’s happening. 

Currently running 7psi with a manual boost tee 

Any ideas what it could be? Have checked the afm and it seems fine, vacuum lines are fine and can’t find any boost leaks ( it holds boost as long as it’s less than 6psi ) 

im thinking it might be coilpacks, spark plugs or tps but don’t really want to start buying parts until I know what I need so I don’t replace stuff that isn’t broken 

 

 

Link to comment
https://www.sau.com.au/forums/topic/475496-r33cutting-out-at-7psi/
Share on other sites

How high in the rev rang do you hit 6psi before this happens?

Do you have any aftermarket ECU?

Read this topic.

https://www.sau.com.au/forums/topic/336073-r33-rb25det-cutting-out-on-boost/ 

5 hours ago, Robocop2310 said:

How high in the rev rang do you hit 6psi before this happens?

Do you have any aftermarket ECU?

Read this topic.

https://www.sau.com.au/forums/topic/336073-r33-rb25det-cutting-out-on-boost/ 

The tacho doesn’t work but I’d say it’s somewhere around 4-5k revs 

stock ecu

Update: have changed spark plugs ( regapped to 0.9 ) and it seems to have stopped the boost cut but now it’s misfiring under load, changed the coilpacks too and didn’t change anything. 

Is fine if I drive really quiet but if I put my foot anymore than half way down it just sits there farting . Any ideas what could be causing it? Will have a look at the fuel pressure but I’m thinking it’s something to do with the plugs as it got worse when I changed the spark plugs 

wouldn't surprise me if both sets are cooked... Borrow set of decent coils that aren't yellow or red in colour.

If S1 check ignitor/swap it AND check the ignition harness (clean or replace or hit it with WD40)
if S2 check the ignition harness (clean or replace or hit it with WD40)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ha, I've never pressed the X in all these years incase it removed the notification for all Admins
    • I don't know, I've never done it that way, but 1. While it is an interference engine, there is still clearance between the valves and the piston at all points in the regular timing cycle 2. There is not a lot of distance before you can't catch the top of the valve stem any more I don't know if 2 is greater or less than 1. But 3. If it doesn't work out you are f**ked, engine is coming out to disassemble so it is a big bet.
    • Semi slicks are horrible for road use, just use a high performance road tyre unless you really need the maximum grip. Noisy, unpredictable (amazing, until they are not), expensive due to very high wear and not good in cold and particular wet. And yes, it is a thing to store cars on stands instead of tyres if you know they are going to be parked up long term.....but who ever realises that a short park is going to stretch into years before it is out again!
    • I know in Australia you'll definitely get above 30c. Parked in the shade in Summer you'll be above that. 😛 But in cooler climates, you might get that warm driving on the highway for a bit, but you'd never get to full heat temp. I'll try and find some of my historical tyre temps between Aus summer and winter (be aware immin the warmer area of Aus too.)
    • I get that taking off the head is best but that's a bit much for "just" valve seals. I was just under the impression that one would be able to rotate to TDC and be able to temporarily drop the valve without losing it and effectively having to remove the head to then recover it. I never knew people actually pushed rope into the cylinder to do valve seals hahaha So just to confirm, just going to TDC will not work? In that case I know when I do valve seals I'll maybe just remove the head and do some other things while I'm there, or just wait until I do an engine build.
×
×
  • Create New...