Jump to content
SAU Community

Recommended Posts

  • 3 months later...

Cut the sump and Luke laffan welded it up for me. Moved the pickup to the centre of the pan and have the whole oiling system and parts sorted.

Luke is building a 142 rally car, some of you may have seen it on the Facebook pages. it is going to be incredible!

 

 

MVIMG_20190726_141115.jpg

MVIMG_20190727_170928.jpg

  • Like 2
  • 1 month later...
  • 2 months later...
  • 6 months later...

So quite a lot has happened since I last posted.

I've finished the wiring in the engine bay. The engine and car are still on separate looms so the engine setup can be put into something else or the car can have a B20 put back in very easily.

I've also started on the interior wiring where all of the cars wiring is now tucked out of the way ready for the corollas looms to be put in. But i'll probably test start the engine before that.

After doing all the front end wiring i chucked a battery in and i couldn't get anything to work.. No lights, no power, nothing... After thinking of the worst things possible i moved the ground and everything lit up! I was about ready to burn the thing to the ground.

 

 

The oil system is finished. I tried to make a neat package that is hidden and not a total mess. The setup is very modular and free flowing. The cooler is placed just behind the air intake on the bottom lip, so it is also functional and it will put a little more weight over the front end.

I'm a bit worried about the weight, if all the numbers on the internet are true ill be way too light in the front, and there isn't much that can be taken from the rear, the boot can be skinned and things like brackets etc can come off but there isn't much else. I came up with a 40/60 split taking into account all the weights i've found online for the 142.. I really need to corner weight the car to see exactly what it is.

 

Made a new belt and pulley system. I got a 6 rib pulley for the tensioner arm. Most people will use an idler off to the left, but i've got a steering box there.

 

Plenum is now finished. I used a 4g63 plenum and cut and modified it to fit on the 2zz flange and throttle body. I chose this plenum and it matches up with the 2zz fairly well, has bellmouths for each runner, the shape, and it's not absolutely massive like others. Everything follows another line so it looks like it's meant to be there.

 

The only other thing to do is to fill it with oil. Do the fuel lines. Plug everything in and start it.

I'm a bit anxious about it because I've done so much wiring on the engine and haven't even plugged it in to make sure it all works.

 

 

 

MVIMG_20200601_164816.jpg

MVIMG_20200601_164826.jpg

MVIMG_20200614_063943.jpg

MVIMG_20200614_064408.jpg

IMG_20200517_141601.jpg

IMG_20200517_141611.jpg

IMG_20200517_141907.jpg

MVIMG_20200517_144633.jpg

MVIMG_20200517_144711.jpg

MVIMG_20200528_163414.jpg

MVIMG_20200528_163425.jpg

MVIMG_20200529_143042.jpg

MVIMG_20200530_201446.jpg

MVIMG_20200601_164811.jpg

  • Like 2
On 14/06/2020 at 8:16 AM, Trex said:

I'm a bit worried about the weight, if all the numbers on the internet are true ill be way too light in the front, and there isn't much that can be taken from the rear, the boot can be skinned and things like brackets etc can come off but there isn't much else. I came up with a 40/60 split taking into account all the weights i've found online for the 142.. I really need to corner weight the car to see exactly what it is.

One solution to balance the weight is to strap a Promod 88 to the side. 

  • Like 2
  • Haha 2
  • 3 weeks later...
  • 3 weeks later...

So now the engine runs. The manifold and downpipe can be welded properly. The flange on the plenum is a little warped, hence the rough running, so ill flatten that. Thats pretty much the engine complete.

This pandemic has made it hard to order parts, you really need to be careful where you order things from and make sure theyre in stock... Waiting months for parts is pretty frustrating.

 

 

The engine bay and interior loom still needs a few hours of cutting and de pinning. I'll wait till its running and driving before i complete it as i still need a speed signal for lift to engage.

I'm currently working on the getrag 250g.

 

clutch- The getrag uses a 228mm clutch disc while the 2zz flywheel and pressure plate are setup for a 212-216mm disc. I got a bmw e30 clutch disc which is 212x8.5 and a 10 spline input. and it works perfectly! The best part about this is, there are plenty 10 spline clutches in different configurations that are the same dimensions.

 

The pivot ball, release bearing shaft, and slave cylinder pushrod needs to be moved outward.

To make the fork parallel to the bearing and clutch fingers a 15mm spacer needs to me made for the release bearing shaft. This will ensure the bearing is parallel when disengaging the clutch and not binding.

The pivot ball is a little plastic cone with inbuilt fork clip. Matt from the development labs (check out his abandoned and submerged r33 race car he is rescuing) came over as he was in town and helped on the build the last few nights. He has drawn me up a cad drawing to make an extension which will be stackable depending on what pressure plate i may change to down the track.

The pushrod is just some allthread with a dome cap on the end. For the standard clutch and pressure plate this is fine, but if i do eventually change to a stronger pressure plate this will have to be revised.

 

The pilot bearing is a holden 304/308 item which gives the snout of the getrag 12.8mm of engagement into the back of the crank.

 

The belhousing to block will need to be doweled. The standard tolerance for runout of the clutch is 0.1mm. noting that the 2zz spins at 8500rpm, im not really willing to have anymore than that.. I'll also be using a scatter blanket just incase that input shaft decides it wants to let go.

 

I had a bit of a look at the bolt situation for the belhousing to block. I can see about 6 possible spots to easily connect them together, more if i make brackets.

  • Like 1
  • 1 year later...

Soo much, too much has been done since my last post. Like most of my projects, I've taken it too far.

I've been driving it around and having a lot of fun getting it setup and dialled in. Will have to do a proper post later on. 

 

 

PXL_20220305_235945981.jpg

PXL_20220211_235442531.jpg

PXL_20220211_235312958.MP.jpg

  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...