Jump to content
SAU Community

Recommended Posts

was wondering in the stagea would be capable of towing a old 521 datsun ute, total weight would be about 1600-1700kg inlcuding a trailer, with hills, because new zealand, these are a couple photos of the tow bar and mount, the mounts go either side of the spare wheel to the rails, asking as the rating sticker has been faded but at a guess it would be only 1200kg from what i have read on here

55957808_348464929209644_4394163774769070080_n.jpg

56398397_440365256524713_1221720541317038080_n.jpg

56618801_367507387190466_3276571541562720256_n.jpg

Edited by darksould43
Link to comment
https://www.sau.com.au/forums/topic/476518-towing-a-datsun-with-stagea-m35/
Share on other sites

Any brakes on the trailer? I haven't had a look under the back of an M35 but from other posts it seems you need to be very careful to reinforce places where you bolt the tow bar up. I would take the risk,   driving very carefully,  but be aware of the potential weakness.

6 hours ago, KiwiRS4T said:

Any brakes on the trailer? I haven't had a look under the back of an M35 but from other posts it seems you need to be very careful to reinforce places where you bolt the tow bar up. I would take the risk,   driving very carefully,  but be aware of the potential weakness.

Yes trailer brakes 

10 hours ago, KiwiRS4T said:

Any brakes on the trailer? I haven't had a look under the back of an M35 but from other posts it seems you need to be very careful to reinforce places where you bolt the tow bar up. I would take the risk,   driving very carefully,  but be aware of the potential weakness.

Exactly what I would do too, assuming its's also not too far (or if it is, regular stop and looks). But I'm no engineer or NZ road law expert

6 hours ago, Duncan said:

Exactly what I would do too, assuming its's also not too far (or if it is, regular stop and looks). But I'm no engineer or NZ road law expert

It is a distance, close to 4 hours, 300 km, couple hills, and I would stop every now and then to let it cool down 

It's no so much the cooling down as it is the brakes, the strength of the chassis (which will stretch if pulling more load than it can handle, especially uphill).

Just rolling along for hundreds of km at a steady speed won't cause any grief at all, except with the coppers if they decide you look like you belong on Highway Patrol.

30 minutes ago, GTSBoy said:

It's no so much the cooling down as it is the brakes, the strength of the chassis (which will stretch if pulling more load than it can handle, especially uphill).

Just rolling along for hundreds of km at a steady speed won't cause any grief at all, except with the coppers if they decide you look like you belong on Highway Patrol.

well ill keep that in mind, there maybe routes to take without hills, thought the hills arent massive ones either

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I now seem to be limited in power due to my rev limit/hydraulic lifters in my built RB25. I'm looking into converting over to Tomei solid lifters. Question for anyone that has done the conversion. I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  I don't know where I got this idea, as so far I see no mention of this in any of the Tomei documentation. It just states I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
    • I couldn't agree more. I should have started from the get-go with a NEO or solid bucket conversion. I started looking into converting over to solid lifters yesterday. Now for some reason I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  But I see no mention of this on any of the Tomei documentation. It just states that I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
    • BRUH, one of the biggest mistakes of my life..... and i've had plenty ;[)
    • @Murray_Calavera iam just considering options 🙂 of course it is very expensive so that why i ask here 🙂  @joshuaho96 I looked at that GCG hybrid(i remember looking at it few weeks before) So this is "that" hybrid where i send them my turbo and they upgrade the inside to Garrett stuff and then they send it back. It cost around 1200-1300 USD which is FAR cheaper than the HKS and it is what iam looking for(i just do not have experience like this...to send something off to "upgrade" ) @tylink720 that is like 150 USD turbo no? 😄 I dont think i have the "ease on my mind" with this kind of turbo. I just put over 7000k USD to "LINK" up my engine...dont want to blow it up with cheap turbo 😄     EDIT: https://www.cj-motor.com/gcg-turbo-charger-for-nissan-rb20det-rb25det-high?srsltid=AfmBOooVeOZ6CZ6r1AIv5m-KPaa6BvudIPJTY8LW78khkd-gQlsaCht9 I looked at this and it seems ok? It is that CGC hybrid and it costs around 1250 USD (with back shipping). Do any of you have experience with this hybrid on NEO turbo? I quickly look thru the forum/web and it seems very good.
    • Echo the awesome sentiment 👍 Definitely a car worth saving. Looking forward to seeing updates as well. 
×
×
  • Create New...