Jump to content
SAU Community

Recommended Posts

Hi all, so I'v done a rb20de+t neo conversion in my r33, if opted with the rb25de loom 25de intake, with a rb25de cas, it was going 1 day, I ran outr gas the next now it will crank over but wont start,, I have spark and fuel, maybe thinking my cam angle sensor is dead,,, I'm in the middle of sourcing a new 1 but was told a normal rb25de cas can not work on a neo engine,,, help help bit stuck. Thanks for your time to read and maybe help a brother out.....

Link to comment
https://www.sau.com.au/forums/topic/477236-r33-rb20det-neo-conversion/
Share on other sites

You'll need a CAS that suits the exhaust cam as the spline on the exhaust cam is different on the neo compared to a S1 or S2 rb25. If you're using the rb25de loom/ecu you'll then need to flip the two end wires of the CAS plug. I assume you would have already done this if the car has been running?

What made you think the CAS died?

Edited by jmknights93
53 minutes ago, Deangelo said:

Hi all, so I'v done a rb20de+t neo conversion in my r33, if opted with the rb25de loom 25de intake, with a rb25de cas, it was going 1 day, I ran outr gas the next now it will crank over but wont start,, I have spark and fuel, maybe thinking my cam angle sensor is dead,,, I'm in the middle of sourcing a new 1 but was told a normal rb25de cas can not work on a neo engine,,, help help bit stuck. Thanks for your time to read and maybe help a brother out.....

Just to be clear have you had this car driving properly or did the engine just fire once then die? You have the right ECU? You have fuel but is it enough - have you checked the pressure? You ran out of gas is there dirt in the system? Have you taken the CAS off to see if it spins freely?

Yes I'm using a rb25det manual ecu, yes cas spins freely,,, I'm assuming theres enough gas getting thru, iv had it runing for months then suddenly ran outr gas and hasnt start since, engine turns over fine,,, just the 1 day I put my drive shaft and and manual conversion in and wont blaaaardy start,

2 hours ago, Deangelo said:

Yes I'm using a rb25det manual ecu, yes cas spins freely,,, I'm assuming theres enough gas getting thru, iv had it runing for months then suddenly ran outr gas and hasnt start since, engine turns over fine,,, just the 1 day I put my drive shaft and and manual conversion in and wont blaaaardy start,

OK so have you had it running in manual mode? You have shorted out the fuses under the battery (to disable the lock out that stops it starting in anything but P and N)?

8 hours ago, Deangelo said:

I was low on gas (I no dumb) and was working on my car had it running and cut out,,  but what's your thoughts?? All thoughts on this is more than welcome thanks,

i get the feeling there are more things going on that we dont know about. the likelihood of the cas failing at the same time as the "running out of fuel" incident doesnt make sense.

both above posts are quite relevent

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...