Jump to content
SAU Community

Recommended Posts

My current wheels have cracked so I've finally bought a new set of wheels that I've eyeing for a while. Problem is, the wheels are apparently too big. My current wheels are 18x8 (+38) on the front, and 18x9 (+22) on the rear. My new wheels are 18x10 (+38) all around, and while the rears fit just fine the fronts are hitting the J arms with no space to spare whatsoever. I've put a 10mm spacer to test how much space I'd get and estimated that I'd need another 10-15mm to get the same amount of space between the wheel and the J arm that my 18x8 wheels have. But even without the spacer the wheels stick out past the fender by 25mm, and adding 20-25mm spacers will make it poke out far too much and be too obvious for cops to pull me over and defect me.

My only solutions at the moment are 20-25mm bolt on spacers, and also possibly adjustable camber arms to adjust the camber just enough so that the poke isn't that obvious.

Is there anything else I can do about this? The wheels can't be returned or exchanged. It's just the two front wheels that are the issue. 

Thanks for the replies guys.

The website I bought my wheels from is offering me a large discount on two new wheels and it seems like my only option is to buy new sizes.

will 18x9 fit? Offset options are +38 and +30

Do you know how to calculate how much wheel sticks out and how much wheel sticks in from the hub face, for a given width and offset?

If you do, then you have all the information you need, in your first post, to tell you how a 9" wheel at +30 and +38 offset will sit compared to the ones you have now.

If you don't, then there are plenty of offset calculator app websites that will do the arithmetic for you.

http://marksink.com/tire_wheel_offset/offset.html this is a tool I got from one of the other wheel posts - it's great to check clearances both sides. 18x9+30 should be sweet on a 34 - I was running 18x9.5+15 all round before.

Where did you get the wheels from? 

Edited by Moshpit95

 

1 hour ago, GTSBoy said:

Do you know how to calculate how much wheel sticks out and how much wheel sticks in from the hub face, for a given width and offset?

If you do, then you have all the information you need, in your first post, to tell you how a 9" wheel at +30 and +38 offset will sit compared to the ones you have now.

If you don't, then there are plenty of offset calculator app websites that will do the arithmetic for you.

 

50 minutes ago, Moshpit95 said:

http://marksink.com/tire_wheel_offset/offset.html this is a tool I got from one of the other wheel posts - it's great to check clearances both sides. 18x9+30 should be sweet on a 34 - I was running 18x9.5+15 all round before.

Where did you get the wheels from? 

I used the offset calculator and it says that with the 18x9 +30 wheels the clearance from the strut housing to the inside of the wheel will be 5mm less, and the outside edge of the wheel will extend an extra 21mm.

I bought the wheels from JDM Concept's website

Edited by sparksflynn
11 minutes ago, sparksflynn said:

I used the offset calculator and it says that with the 18x9 +30 wheels the clearance from the strut housing to the inside of the wheel will be 5mm less, and the outside edge of the wheel will extend an extra 21mm.

I bought the wheels from JDM Concept's website

Yeah that would be going from your original wheels, from the 10+38 to 9+30 youll get 21mm MORE clearance and will RETRACT 5mm toward the body.

 go to the last page you can see a yellow skyline running the front 9+30 and rear 10+38 from JDM Concept.

What colour / style are they because I'm actually looking at getting some through them later this year..

31 minutes ago, Moshpit95 said:

Yeah that would be going from your original wheels, from the 10+38 to 9+30 youll get 21mm MORE clearance and will RETRACT 5mm toward the body.

 go to the last page you can see a yellow skyline running the front 9+30 and rear 10+38 from JDM Concept.

What colour / style are they because I'm actually looking at getting some through them later this year..

I got the 1P GT5s in bronze, which is actually the same wheels that the yellow skyline in the linked discussion has. They're quite nice in person. I've test-fitted the 18x10 +38 on the rears and it fits flush on my 4-door R34 compared to the way it fits on the yellow skyline, most likely because of the flared fender. 

Edited by sparksflynn

18x9 +30 can fit without issues. I have them on my car. I have rolled guards and 265's all round. It is very tight.

However, they definitely will, absolutely, fit. I would say a 18x9 +38 on the front would be pushing it to the point where it will both look worse and also not fit. So fk that off.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...