Jump to content
SAU Community

Recommended Posts

I recently purchased my first bnr32 and I am pumped!! It has nismo coilovers but otherwisebis pretty much stock. I will be adding power to it soon, and found a good deal on some r33 brembo calipers only. I have a few questions. I have searched ALOT but havent found an answer yet. 

1. What rotors do i use? Im wanting 2 piece rotors and want to know what to buy. 

2. What brake lines do i go with? Im wanting steel lines and dont know if i will need custom or not. 

3. What brake master cylinder? My car is a 94 and im pretty sure it has abs so im think the bm57? Will a 300zx one work or does it have to be an r33 or r32 one? 

Thank you for the help!

 

Link to comment
https://www.sau.com.au/forums/topic/479984-r33-gtr-brembos-on-r32-gtr/
Share on other sites

Well, this has kind of been covered here before, and I don't know where you are because you didn't fill in the location field of your profile....but answers are:

1. You need to move from 296mm rotor to 324mm rotor for r33/r34 gtr. eg DB5928 for 2 piece slotted.

2. Standard lines fit fine. R33/34 brembos were standard fitment on R32 vspec I and II models too.

3. Keep the standard master cylinder, it will be fine. 

You may need to trim or push back the backing plates behind the rotors, but otherwise that is a straight fit upgrade to an r32.

  • Like 1
2 hours ago, Dose Pipe Sutututu said:

You will need 326mm rotors. DBA have both 1 piece and 2 piece if you have money to burn.

I can help with rotors and pads please DM.

typo sorry :(

DBA4928 = DBA4000

DBA5928.1S = DBA5000

hey m8 mise well install a new set of pads while you got the caliper out. will last a very long time if so. might even be good time to have the calipers powder coated with a new Brembo decal keeping her clean! I wish I did this with mine before I got horny and just threw them on for 50 thousand km lol they have become faded and need a facelift. the backplate for caliper I had to cut a bit. here's a pic of mine installed with regas. took me 1.5 hour per side taking my time. 

  • Thanks 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...