Jump to content
SAU Community

Recommended Posts

All, 

I have painted over years but with minimal knowledge so I am trying to up my knowledge.

 

here are my qestions:

paint procedure is as follow with points needed to be done on each stage, is that correct ?

1. Primer( if bare metal) or grit 1500 to create area for paint to stick if there is already paint. This will be 1 to 2 coat. one needs to wait 24 hours before going from primer to sanding to doing base coat.

2.Base coat, 2 to 3 coat. some say 4 to 5 coat which ?
Waiting around 15 mins after each coat.

3. top coat, I don't really understand what this is, what is the top layer?

4.laccuqer or clear coat , 3 to 4 coat. around 15 to 20 mins after each coat 

5.polish 

 

temperature is what is I have in garage which is around 15 to 20 degree.

I have painted a metalic car using above and paint is sort of matt , is there specific laquer to be used with metallic?

 

 

Link to comment
https://www.sau.com.au/forums/topic/480620-few-general-questions/
Share on other sites

After the first coat you give it a sand and hollows etc will show up  for you to fill. Top coat is the last coat. Laquer is for show cars...shows up every deficiency in the metal.  Requires many coats. Enamel is easier and more forgiving.

8 hours ago, drifter17a said:

When you say sand with 600?

 

would you fill hollow with bonding compound or next layer of paint

 

 

Depends on how deep the hollows - there is a special spray on stuff you can apply locally.  Have done some painting but I'm no expert ...have a look at the pros on YouTube.  Also you can get free advice from the auto paint shops.

On 17/06/2020 at 3:29 AM, drifter17a said:

All, 

I have painted over years but with minimal knowledge so I am trying to up my knowledge.

 

here are my qestions:

paint procedure is as follow with points needed to be done on each stage, is that correct ?

1. Primer( if bare metal) or grit 1500 to create area for paint to stick if there is already paint. This will be 1 to 2 coat. one needs to wait 24 hours before going from primer to sanding to doing base coat.

2.Base coat, 2 to 3 coat. some say 4 to 5 coat which ?
Waiting around 15 mins after each coat.

3. top coat, I don't really understand what this is, what is the top layer?

4.laccuqer or clear coat , 3 to 4 coat. around 15 to 20 mins after each coat 

5.polish 

 

temperature is what is I have in garage which is around 15 to 20 degree.

I have painted a metalic car using above and paint is sort of matt , is there specific laquer to be used with metallic?

 

 

hi mate,

some paints require a Ground Coat which is usually the metallic colours. just double check if you need this or not.

I wouldn't fill the minor scratches with bog.. just use primer filler or a spray putty.

just to make it clear. will you be using acrylic paint or twopac? I would not recommend using two pac paint in a garage as you need a proper booth. with acrylic you can get away spraying your car in your garage and depending on the coverage I would personally put on 3-5 coats and 3-4 coats of clear on top. 

Also, with acrylic paint, you need to wait for to paint to cure for couple of days, wet sand and and cut and polish after.

 

Thanks bud

 

would ground coat be same as the first wet laquer before base coat, seen that on youtube and didn't understand it
 

when you donbase coat, i was 15 mins between coats and after 30 mins following last coat do laquer or clear coat otherwise as I understand you need to sand it with 1000 to create but surface if doing it say next day

 

re paint types, i know mine is metallic but don’t really know different type of paint and whether mine is acrylic

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
×
×
  • Create New...