Jump to content
SAU Community

Recommended Posts

All,

 

had car for number of years all good. Changed to big turbo and around 650bhp and after 2 days of driving alternator suddenly died

 

it is much hotter running car so thinking it could have killed it. Very strange no sign and suddenly dead

 

do they have a relay or something? If i remove battery lead, it dies and don’t charge

 

checked online and some say it could be relay. Is there relay for alternator ?

 

looking at high amp ones they are £600 so pricey.

 

thanks for any advice 

Link to comment
https://www.sau.com.au/forums/topic/480933-r34-alternator-died-suddenly/
Share on other sites

2 hours ago, drifter17a said:

Well not charging do dead for dure ubless there are relay etc

There is dead, and there is dead. What part of the alternator has died? Rectifier? Winding gone open? Dirty commutator?

Diagnose properly, then fix. If this means taking it to a sparky, then do so.

So took it to sparky and he reconditioned it.

 

he couldn’t get the regulator and after some fafing around he called and said it is ready

So now with full load it is charging at 14 but when rpm is 2k and above. When on idle which is around 800 it doesn’t charge at all with full load charing at 12.7 or less with nonload or full load around 11.5 

 

belt is as tight as hell so what could be wrong?

Did voltage drop test and negative it is 2.4 volt and positive is 3.4 volt to alternator and i belive more than 2v on positive and 1v on negative means trouble

 

my battery is in boot so i used jumper lead to extend so not sure if this is playing a role 

 

i think it is either dirty connection or short circuit somewhere, thought?

5 hours ago, Dil-Dog said:

This is from the states, very good price and i have been using this on my r34 for 8 months now. https://frsport.com/circuit-sports-alt-0v017-al-oe-alternator-nissan-r34-rb25det-neo-r34-rb26dett

I'm using one too, no voltage problems with 3x fuel pumps running albeit 2x are PWM.

Good value.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...