Jump to content
SAU Community

Recommended Posts

Hi,

My stock fuel pump was making a hell of a noise so I got a Walbro GCA3386-2 (255LPH)

The mounting is different from stock. With this the strainer attaches directly to the pump while the stock pump sits about half way down the mounting bracket with a pipe to the strainer at the bottom. So with this the pump has to be mounted at the bottom of the bracket. 

Not sure what is the cause but on boost the car is running very lean. AFR is showing 18:1

On normal driving its fine.

The car has a Haltech fitted. Am I supposed to get it remapped after fitting the pump?

Do i need to change the FPR from the stock one?

Link to comment
https://www.sau.com.au/forums/topic/481207-leaning-out-after-new-fuel-pump/
Share on other sites

Was it a stock pump that was removed? if you have gone to a smaller pump that will cause the lean issue.
The walbro also require a wiring & relay upgrade as they draw a lot more current than the standard pump.

No need for retune after a pump swap but if its going lean check vac line to fuel reg, pump part numbers and that the filter on the pump isn't blocked.
 

Thanks Rob. I didnt know it requires a wiring and relay upgrade. Is it to do with the "relay mod" that some other threads mention?

Can you give any more detail on the wiring upgrade?

The vacuum line from the intake mani to the FPR  is fine. 

The new pump came with its own strainer. So that is new. I forgot to change the fuel filter in the engine bay. Will change that too.

 

10 hours ago, Die$eL said:

Can you give any more detail on the wiring upgrade?

It's just a case of giving the pump a decently thick power feed (and decently thick earth to go with it!) that is no longer passing through the original fuel pump controller. The relay allows you to switch the power to the pump however you like/need (ie, possibly still with the fuel pump controller) but the relay makes the power path direct from a main 12V +ve to the pump. Fatter wires to carry the current without burning up or causing voltage drop problems.

15 hours ago, Die$eL said:

 

Can you give any more detail on the wiring upgrade?

 

Generally I use a 50 amp relay, 40amp fuse with 5mm wire for positive and 3mm for negative. Either use an uninsulated crimp and pot the factory cap connection or use a new bulk head

https://www.efihardware.com/image/4937/Submersible-Pump-bulk-head-terminal

 

Most big pumps like the walbro 460l will draw 22-27amps at full load so I like to make sure it's up to the task. Even the old 255l will draw 14amp at idle and 22amps at full load. 

Did you change the fuel filter at the same time @Die$eL? Because if you didn't, there's a fair chance that is your problem. The filter will be full off contamination, including brass from the failed pump.

Thanks for the detailed info. This really helps.

I will upgrade the wiring, relay and change fuel filter then report back. 

Edited by Die$eL
  • Like 1
  • 4 weeks later...

A Big thank you for all of the advice. 

I've upgrade the wiring and this has resolved the leaning out issue. 

I've done a video detailing what I did and bits used etc. Hopefully it can help others who experience the same issue.

 

  • Like 1
On 9/26/2020 at 11:42 AM, White GTS-T said:

Did you change the fuel filter at the same time @Die$eL? Because if you didn't, there's a fair chance that is your problem. The filter will be full off contamination, including brass from the failed pump.

I've decided to run the car for a little before changing the filter just incase there was any contamination which got in while i was working in there. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
×
×
  • Create New...