Jump to content
SAU Community

Recommended Posts

hicas is only very slight turning of the rear wheels, i think the movement is 1 degree at the most. And im fairly sure it only starts working at high speeds

I feel it every now and then, and yes it is a little scary, especially if the road isnt flat and straight

I figure whenever u wanna go fast, cut the speed sensor wire and kill 2 birds with 1 stone :) no speed limiter & no hicas

It sucks if your going to do track work.

Your trying to correct the car in a corner and the car's trying to correct you. Tug of war that results in time loss. So that's why it's recommended that you remove it for track.

I have the Tomei Lock kit, which has the brass washer looking things, and some sort of gdaget that is wired in and fools the ECU, just been to lazy to get it installed.

The Drift battle mag in front of me has em advertised at hi-octane for $245.

I got mine for half that 2nd hand.

Skylinegeoff also has the lock bars for sale I think?

It's not actually that bad, and since you've got an R32, it'll be hydralic, not a computer. Make you feel better? :rofl:

It's a very subtle thing... the rear wheels deflect maybe 1 degree... but when you reef it around a corner at 70-80, HICAS tries to sort out what you're doing, not thinking that you're being a hoon, and tries to save you from destroying yourself... which you're trying to do on purpose, so it can be a little... frustrating. The worst it does is gives the bum end a little wiggle when cornering hard... which like it was stated before, sucks on a track.

well i have a R31 with HICAS and it works even when stationary, dont know about later models though. Just looking at it and turning the wheel you would think it aint moving but it is.

As stated above, with normal day to day driving you would not know it is there.

But when I am driving around a long sweeping bend at speed it starts to wriggle the arse end about which feels very hairy. I also plan to remove it.

When you get the car, find a roundabout and start driving around it, slowly increasing your speed. At the start you feel in control of the car but as you get faster you feel the hicas come into play and try to work against you.

HICAS on an R32 is inactive at low speeds & fairly passive most of the time. It doesn't so much correct you, its more about aiding more responsive turn in and increasing stability mid corner.

/searches for diagram from R32 brochure...... fails :)

Basically:

At intermediate speeds it will angle the rear wheels opposite on inital turn-in to to sharpen the turning response, then angles them the same way as the front for mid corner stability.

At high speeds it does the same minus the initial turn-in opposite angling, the idea being that at higher speed you need less turn in response.

Unless the system is playing up or you entend on doing a bit of track work I really wouldn't worry to much about it.

I've got the Tomei locking kit and my Hicas warning light still comes on whenever I'm pushing it around a corner. I'm going to grab a Kazama lock bar to make sure it's hicas-less...

It's lighting up to tell you there's an error with HICAS... namely there's two metal collars stopping it from moving. :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...