Jump to content
SAU Community

Recommended Posts

8 hours ago, QLDR31 said:

Apparently the NEO has no washer in the inlet cam.

image.thumb.png.0c1bcecb1c4fc791e890b41b00506b03.png

On the weekend I got the timing belt on. Did another rookie error had my torque wrench set to fp instead of nm. Over torqued the tensioner. So I tossed my new stud and nut and reused my old ones.

I bought a stud install/remove kit. The remove part is too long to remove the tensioner studs but the install part works well. I loctited the smaller stud.

My engine didn't have original the cam cover bolts so I have ordered them (another 3-4 week wait). Apparently the NEO bolts are different to everything else. But I have plenty to go on with.

image.thumb.jpeg.ef55564564dd1f7db0acc275ff380d54.jpeg

Just make sure it has NEO cam covers as that’s why the bolts are different. The gasket on NEO covers is different as well

  • Like 1
  • 1 month later...
On 3/15/2023 at 5:41 AM, RBW49N said:

Just make sure it has NEO cam covers as that’s why the bolts are different. The gasket on NEO covers is different as well

Thanks, I didn't know that. I got cam cover gaskets in the OEM gasket kit so should be ok.

I bought a 29 piece silicon hose set today on eBay under $445 with tax. See how it goes.

The other day my cam cover bolts turned up and surprise surprise they look like what I already had. I knew they were different to older RB engines but didn't realize they were normal looking bolts.

 

2 hours ago, QLDR31 said:

Thanks, I didn't know that. I got cam cover gaskets in the OEM gasket kit so should be ok.

I bought a 29 piece silicon hose set today on eBay under $445 with tax. See how it goes.

The other day my cam cover bolts turned up and surprise surprise they look like what I already had. I knew they were different to older RB engines but didn't realize they were normal looking bolts.

 

Yeah they look like bolts someone found lying around the shed don’t they. 

On 4/23/2023 at 2:42 PM, RBW49N said:

Yeah they look like bolts someone found lying around the shed don’t they. 

O well I got shiny new ones now. Would of preferred to save the $60 for something else.

I noticed the oil cooler has a tiny leak so I bought three the o'rings for that. I thought they would be with the gasket kit. R33 manual says to torque oil cooler to oil filter bracket to 34-44nm.

Bolted on the exhaust manifold. My R33 manual said 3.9-4.9nm. Think this was a typo the exhaust heat cover are that torque. Another part of the manual says 27-31nm,

I still haven't bolted on the balancer. I was waiting till I have complete inlet and exhaust manifolds bolted on. Then hoist it up, bolt on the flywheel (so I can use it to lock the crankshaft). Then bolt the balancer on, timing belt covers and cam covers. Hopefully will be ready to drop in the engine bay by then.

Tips on torquing the cam covers? R33 manual says 2-3.9nm. Not sure how I can do this maybe hand tight. My 1/4inch torque wrench only goes down to 5nm.

4 minutes ago, QLDR31 said:

Not sure how I can do this maybe hand tight.

Exert about half the force required to make the 1/4" TW go click when set to 5, and call it done? Or just do them up to 5 on the basis that 2-4 Nm is barely more than a sneeze? Is your TW even sufficiently calibrated to know the difference between 4 and 5 Nm?

  • Like 1
  • 2 weeks later...

The silicon hoses turned up yesterday. Most of them seem to match up. So do I need new hose clamps everywhere?

image.thumb.jpeg.557d802ef1b1e3ed68ee805bfce13457.jpeg

Thinking of tidying up the coolant hard pipes. I'm thinking: wire brush and rust disolver rusty bits. Clean off oil and grease and some silver gal paint.

image.thumb.jpeg.17686b07440d06c8d31c77a96210123c.jpeg

Replaced orange with black o'rings on the oil cooler. Also did the one between the block and the sandwich plate.

image.thumb.jpeg.b9b73b0d5dc987c53e479ed16ecc876f.jpeg

20 hours ago, QLDR31 said:

So do I need new hose clamps everywhere?

I reused most of the OEM spring clamps, you could replace the clamps if you wish, no real harm.

  • Like 1
  • 1 month later...

I was putting new o'rings on the injectors today. Then I was trying to put the insulator? at the tip of the injector. They seem to break. I guess I'll need some new ones? Any tips?

image.thumb.jpeg.0a69e017d64f28adb8da27760cc130ee.jpeg

Slowly progressing:

image.thumb.jpeg.2ca4c5fc77e37bb95ddc2098e2209600.jpeg

  • Like 1
15 hours ago, QLDR31 said:

I was putting new o'rings on the injectors today. Then I was trying to put the insulator? at the tip of the injector. They seem to break. I guess I'll need some new ones? Any tips?

image.thumb.jpeg.0a69e017d64f28adb8da27760cc130ee.jpeg

Slowly progressing:

image.thumb.jpeg.2ca4c5fc77e37bb95ddc2098e2209600.jpeg

Looking good

Last weekend I got the harmonic balancer on, had to bolt the auto flywheel on so I could lock it with a thing I made up. Then removed the flywheel again. So I could bolt the engine back on the stand.

IMG_20230625_152105.thumb.jpg.91c57af57bcb1b29634e129a95d5f046.jpg

Also got the injectors on. The insulator things on the tips of injectors I managed to find 6 unbroken ones heated them up with heat gun and put them on. Luckily I had a spare set of injectors and rail to raid parts off.

This weekend i'm planning on bolting down the cam covers (buying a 1/4" torque wrench that goes down to 2Nm),  I got alloy cam halfmoon blockers, Bolting on the turbo and covers, bolting on the top of the intake manifold and finishing the plumbing. Should be pretty much ready then.

  • 1 month later...

I cut up some cable tie saddles to secure the coil wiring loom (the threads were already tapped to 5mm). The build is nearly done just need to figure out a few more hoses like the IAC valve and bolt the turbo on. Anyone got a pic of the IAC valve? I'm pretty sure I know how it plumbs just not certain (closest pipe to coils to the red bung in pic, middle pipe to throttle body, last pipe to coolant stuff below via long hose).

 

image.thumb.jpeg.0625aad12513fadd93ad3ee340d01504.jpegimage.thumb.jpeg.5580979a0d40dfddfa7b466a296cb4ca.jpeg

Edited by QLDR31
more info
  • Like 1
  • 4 months later...

The engine and car are now in the same garage. I went to install the engine. It's been sitting in the same spot for a couple weeks. Found an oil leak. Luckily it was just the drain plug. I put the flex plate back on (93-103Nm). I can't find the torque spec for the four torque converter mounting bolts. They are smaller bolts then flex plate so probably less torque. Hopefully New years day i'll get the engine in. I also found a bunch of surface rust around where radiator goes so might tidy that up before putting the radiator in.

  • Like 1
  • 2 months later...

The engine has been in for months now. Unfortunately something is wrong, bell housing bolts are in but there is a gap less than 10mm between bell housing and engine. The engine can't be turned in neutral, so something fowling. Note its an AWD auto and everything is original parts. I was thinking of putting longer bolts in bell housing that way engine and gear box can stay lined up, lever a gap between them and turn the engine until it lines up. Any tips/advice would be helpful. I'm planing on towing it to work so hopefully I can get it running, a few mechanics there to help me.

Definitely no gap is acceptable between engine and gearbox, I'd get it on a hoist, take the box off and check carefully before attempting to put it on again. 

Could be the fouling on the dowels on the engine, could be you have a manual instead of auto spiggot bush in the back of the crank, could be the input shaft was already bent (or it has been bent while installing), not sure what else, I've not dealt with an auto rb

 

 

  • Like 1

Thanks guys.

Hopefully nothing is fooked up.

The converter is meant to be bolted onto auto flywheel first hey? Not later. 

I like the hoist idea, I can do that at work. The tail shaft bolts are tight as fook and auto box is as greasy as fook. I guess ill need to put some wood between the sump and cross member to keep engine in position?

Doesn't have any manual stuff. Same engine and gearbox. That were original.

If the gearbox is busted i'll be looking for manual conversion.

1 hour ago, QLDR31 said:

Thanks guys.

Hopefully nothing is fooked up.

The converter is meant to be bolted onto auto flywheel first hey? Not later. 

I like the hoist idea, I can do that at work. The tail shaft bolts are tight as fook and auto box is as greasy as fook. I guess ill need to put some wood between the sump and cross member to keep engine in position?

Doesn't have any manual stuff. Same engine and gearbox. That were original.

If the gearbox is busted i'll be looking for manual conversion.

No the convertor needs to go onto the gearbox first 

  • Like 1

Thanks guys.

Are you meant to tighten the converter bolts through the starter motor hole?

Think my plate between gearbox and engine is one piece.

Im heading up there tomorrow.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...