Jump to content
SAU Community

Recommended Posts

G'day legends, 

The misses has an R31 GXE Auto which I recently did injector rebuild on. 

I removed the old injectors, had them flow tested and a new seal kit done as there was previously a leak. 
Prior to removal, the main issue was the above mentioned fuel leak, but since completing the reinstallation of the injectors, there has been a really intense misfire. 

-The injectors flow tested perfectly
-A lot of care was taken when installing them, so I don't believe they are will be the issue as of yet. 

So far, I have replaced;
-Dizzy cap and rotor (they were both absolutely cooked)
-CAS (some sort of water entry got in there and made a mess)
-Plugs (Were disgusting)

>The AFM is second hand, and was replaced when the original one died. 
>The Injector plugs are pretty cooked, so that will be my next replacement as it is required anyway. 
>I will need to test the ignition leads, however they were only done about 2 years ago
>Not sure how to check the ignition coil, but seems unlikely it would die straight after the above work was done. (not sure when it was replaced last either)

Sometimes I wonder if I have swapped some electrical connectors around by mistake, but I am confident that they are all in their correct locations. 
I did pressure wash the whole engine bay after the replacement, is it possible I soaked the ECU? (Unsure of ECU location).

Any help would be absolutely amazing, this is doing my head in. 

Cheers!

000024.JPG

ECU is in passenger side footwell.

Take the dizzy apart, make sure the CAS disc inside is clean.

I had misfire issues because the CAS was rusty and spilling dirt on the disc (sensor wasn't reading properly hence misfire).

Also does it idle fine? Try unplugging AFM, it should idle and rev to 2,000 rpm fine.

Loads of info on R31 Skyline club wiki

On 8/17/2021 at 3:50 PM, Birdpirch said:

... I did pressure wash the whole engine bay after the replacement ...

 

This probably won't have done you any favours. A wet connector block somewhere could be upsetting things. Try some WD40in all the connectors.

  • Like 1

Go back to basics man. Compression test. A constant reading is good, a 30 psi or more difference between adjacent cylinders is bad. Disconnect one injector at a time and reconnect until you find the bad cylinder. A good cylinder will run rougher with the injector disconnected. The bad cylinder will do nothing with injector disconnected. Then check for spark. Use a gap tester or remove a spark plug on each cylinder. Don’t forget to remove the fuel pump fuse if you pull the plugs to test. 
 

if all that checks out ok, check for vacuum leaks and injector wiring. 
 

if you’ve pressure washed it you will probably have water somewhere simple, usually in the dizzy cap or spark plug tubes 🙂

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Stop looking at the garage floor, and turn the radio up a bit louder if there's any strange noises...
    • No. Turbo shuffle and surge/flutter are not the same thing. Specifically, on a GTR, turbo shuffle has a definite meaning. On a GTR, the twin turbos are assumed to be the same thing and to operate the same way, exactly. In reality, they do not. Their exhaust sides are fed and exhaust a little differently, to each other. Their inlet sides are fed and exhausted a little differently, to each other. Consequently, when they are "working" they are often at slightly different points on the compressor map compared to each other. What this means, particularly when coming on boost, is that one of them will spool up and start producing extra flow compared to the other, which will put back pressure on that other compressor, which will push the operating point on that other compressor up (vertically). This will generally result in it bumping up against the surge line on the map, but even if it doesn't, it upsets the compressor and you get this surging shuffle back and forth between them That is "turbo shuffle" on a GTR. It is related to other flutter effects heard on other turbo systems, but it is a particular feature of the somewhat crappy outlet piping arrangement on RB26s. There are plenty of mods that have been attempted with varying levels of success. People have ground out and/or welded more material into the twin turbo pipe to try to prevent it. Extending the divider inside it works, removing material doesn't. There are aftermarket replacement twin turbo pipes available, and these exist pretty mush purely because of this shuffle problem.
    • You can temporarily* use lock collars to keep it in place until you can do the bushes, back the nuts off, slide them in, snug back up. *temporarily is often for ever
    • Thanks for the quick reply. To be clear, when you say turbo shuffle do you mean turbo flutter "stustustu" or referring to something else? I had thought they were the same thing. When I wrote the post my intention was to say it wasn't a flutter/compression surge sound. My understanding was that a flutter sound would be occurring when throttle is released, whereas I can keep the throttle in the same position for this noise
×
×
  • Create New...