Jump to content
SAU Community

Sub/Amplifier Problems

blakemcdonnell

By blakemcdonnell,
in Car Audio & Electrical

 Share

Recommended Posts

blakemcdonnell Rookie

blakemcdonnell

Posted
Posted

I recently recieved this sub/amp setup from my uncle for my birthday. 600W MegaVox Competition Amp and 2 x 10" Marathon subs in a Marathon competition sub box. I have a 200W power supply that I used to test them as they are 20-25 years old. When connected to the 200W (12V @ 18A) power supply the subs could play sound (used an RCA to 3.5mm adapter that came with it) but was dropping out, which I assume is to be expected considering I was running a 600W amp off a 200W power supply. After this I installed them in my mates car ( AU Falcon, his wiring was all setup as he has subs of his own) by taking the wiring from his subs and connecting it to mine. When the car was started the amp powered up, but wasn't able to get any sound either from the head unit or the 3.5mm jack adaptor. Checked the voltage running through the power input and it read 14 Volts (normal as AU Falcons charge at 14V apparently). after fiddling around trying to get it to work i took them out and hooked them up to the power supply and it was back to being choppy but could still get sound.

 

Any help or insight into why I can't get sound from the subs in the car but can off a 200W power supply would be greatly appreciated

 

Cheers, Blake

IMG_20211031_223256.jpg

IMG_20211031_223336.jpg

IMG_20211031_223315.jpg

IMG_20211031_223357.jpg

Link to comment
https://www.sau.com.au/forums/topic/482968-subamplifier-problems/
Share on other sites
Ben C34 Grand Master

Ben C34

Posted
Posted
On 10/31/2021 at 10:40 PM, blakemcdonnell said:

I recently recieved this sub/amp setup from my uncle for my birthday. 600W MegaVox Competition Amp and 2 x 10" Marathon subs in a Marathon competition sub box. I have a 200W power supply that I used to test them as they are 20-25 years old. When connected to the 200W (12V @ 18A) power supply the subs could play sound (used an RCA to 3.5mm adapter that came with it) but was dropping out, which I assume is to be expected considering I was running a 600W amp off a 200W power supply. After this I installed them in my mates car ( AU Falcon, his wiring was all setup as he has subs of his own) by taking the wiring from his subs and connecting it to mine. When the car was started the amp powered up, but wasn't able to get any sound either from the head unit or the 3.5mm jack adaptor. Checked the voltage running through the power input and it read 14 Volts (normal as AU Falcons charge at 14V apparently). after fiddling around trying to get it to work i took them out and hooked them up to the power supply and it was back to being choppy but could still get sound.

 

Any help or insight into why I can't get sound from the subs in the car but can off a 200W power supply would be greatly appreciated

 

Cheers, Blake

IMG_20211031_223256.jpg

IMG_20211031_223336.jpg

IMG_20211031_223315.jpg

IMG_20211031_223357.jpg

Not sure why you have bridged the outputs like that.  The actual little wire in the middle isn't needed, and probably causes issues. Take it out and see what happens.

blakemcdonnell Rookie

blakemcdonnell

Posted
  • Author
Posted
On 11/1/2021 at 10:18 AM, Ben C34 said:

Not sure why you have bridged the outputs like that.  The actual little wire in the middle isn't needed, and probably causes issues. Take it out and see what happens.

its the remote/switch input. bridged to power so that it turns on whenever it recieves power. will give it a try soon, just confused as it works fine with power supply but not in the car.

blakemcdonnell Rookie

blakemcdonnell

Posted
  • Author
Posted
On 11/1/2021 at 10:38 AM, blakemcdonnell said:

its the remote/switch input. bridged to power so that it turns on whenever it recieves power. will give it a try soon, just confused as it works fine with power supply but not in the car.

also i thought it could be going into protection mode, but it doesnt make sense to me as the ground works perfectly on his subs and off the power supply both speakers work.

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

The amp is probably going into protection mode with the outputs bridged like that. That's not how you bridge channels together.

They do not act like AA batteries.

Also using that kind of wiring for power will cause more issues.

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

Also with the cost of car audio dropping exponentially, you'll be silly not to run a small footprint marine amp. Here's a fantastic one for the price.

The below amp would destroy what you have there in terms of power delivery, SQ, size, heat manage, etc.

https://frankiesautoelectrics.com.au/clarion-xc2410-400w-micro-size-4-3-2-channel-class-d-marine-amplifier/?gclid=Cj0KCQjw_fiLBhDOARIsAF4khR3wzCm4oVysGSSApkJvO81oVKIuGFZln-lEvBhk6526rHRAXp3pV8caAts8EALw_wcB

Clarion XC2410 400W Micro Size 4/3/2 Channel Class D Marine Amplifier

Ben C34 Grand Master

Ben C34

Posted
Posted
On 11/1/2021 at 10:08 AM, blakemcdonnell said:

its the remote/switch input. bridged to power so that it turns on whenever it recieves power. will give it a try soon, just confused as it works fine with power supply but not in the car.

That's not what I am referring to. There is a wire that shouldn't be there on the speaker outputs.

blakemcdonnell Rookie

blakemcdonnell

Posted
  • Author
Posted
On 11/1/2021 at 10:56 AM, Ben C34 said:

That's not what I am referring to. There is a wire that shouldn't be there on the speaker outputs.

Righto man, cheers. Itll still run without that bridge on both outputs? or will i have to run another cable somewhere?

blakemcdonnell Rookie

blakemcdonnell

Posted
  • Author
Posted
On 11/1/2021 at 10:41 AM, Dose Pipe Sutututu said:

The amp is probably going into protection mode with the outputs bridged like that. That's not how you bridge channels together.

They do not act like AA batteries.

Also using that kind of wiring for power will cause more issues.

Yeah, we were running 50amp wiring in the car this was just the setup we used for the power supply to test it as it was a spur of the moment decision. regarding the output bridging do i just remove the cable bridging the negative to positive and leave it? or do i run speaker wire's from both to the respective parts of the speaker?

 

as you can probably tell im very new to this sort of stuff haha, only time ive hooked up subs had a built in amp and just needed power, ground, remote and input. all other wiring seems alright though?

GTSBoy Grand Master

GTSBoy

Posted
Posted
On 11/1/2021 at 1:41 PM, blakemcdonnell said:

so literally just take it out and it should be fine?

As in.....it won't blow up, which we're all surprised that it hasn't already with the way it is wired now?

Yes.

You should do a little google on what it means to bridge an amp, and how it is achieved, so you at least understand, rather than flying blind.

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

Then the next question, can you even bridge channels with that amp?

There are no physical markings saying you can bridge these channels.

 

Honestly, just buy that Clarion amp I posted up above. Cheaper than a car catching on fire.

blakemcdonnell Rookie

blakemcdonnell

Posted
  • Author
Posted
On 11/1/2021 at 2:33 PM, GTSBoy said:

As in.....it won't blow up, which we're all surprised that it hasn't already with the way it is wired now?

Yes.

You should do a little google on what it means to bridge an amp, and how it is achieved, so you at least understand, rather than flying blind.

 

On 11/1/2021 at 2:39 PM, Dose Pipe Sutututu said:

Then the next question, can you even bridge channels with that amp?

There are no physical markings saying you can bridge these channels.

 

Honestly, just buy that Clarion amp I posted up above. Cheaper than a car catching on fire.

hahaha fair enough, this is just how i recieved them from my uncle. unless hes changed the wiring, this is how he ran it in the 90s. very confused as i cant find anything about the amp on google at all. i will probably end up buying that amp to be honest. what should i be looking for besides on google to see if they can be bridged?

niZmO_Man Grand Master

niZmO_Man

Posted
Posted

Amps probably stuffed, might be a blown capacitor or three. So weird with that wiring setup, I'm surprised it worked haha.

Just get a Class D or mono amp (rated higher than the RMS of the subs, check impedance), save yourself the hassle.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • kike_kike
      Problem with a tachometer on a Skyline R33 with an RB25DET Neo engine

      By kike_kike · Posted

      Hello First, I apologize if this is not the correct forum. Let me know and I will move it to the correct one. I'm having a problem with the tachometer on my Skyline R33 with an RB25DET Neo engine. I'll tell you from the beginning. I'll tell you from the beginning. I have the RB25DET Neo engine installed in a Nissan Patrol GU, with a Link G4X control unit specifically for that engine,  and I have fitted a Skyline R33 tachograph to the original GU dashboard, but it doesn't work properly. I have the tachometer connected to the positive and negative terminals of the GU panel's wiring, and the signal cable is connected directly to the ECU output pin, but the rpm fluctuates widely. Can anyone tell me if the output signal from an R33 ECU is the same as the output signal from an R34 ECU, or if the voltage and signal type are different? Regards and thanks.  
    • Hexi
      Dumb rich kid tries modding for the first time

      By Hexi · Posted

      I guess it was the thought about "Oh if I were to drive this everyday". Then no, SL500 I wouldn't really consider lmao. 
    • Hexi
      Dumb rich kid tries modding for the first time

      By Hexi · Posted

      Yeah actually really fair point. Idk what I was thinking when looking at the SL500. Now that I think about it, I feel like I would have more enjoyment out of a shitbox that I would need to repair than some fancy merc. Although I must admit the SL500 does look quite nice. My bad hahaha.
    • Kinkstaah
      Dumb rich kid tries modding for the first time

      By Kinkstaah · Posted

      100% Also "Not wanting to spend money" is THE WORST IDEA IMAGINABLE when coming to a project car of any kind. They EXIST to BURN MONEY. Sure, gas money is a thing. A stock car with the worst fuel economy ever sold would probably be cheaper than modifying a car with FREE petrol for the life of your ownership of it, lol.
    • MBS206
      Dumb rich kid tries modding for the first time

      By MBS206 · Posted

      Amount of time you're being observed by law enforcement is so minute, that you could be a dumb shit 90% of your driving time, and never lose a demerit. You could also be the best driver ever and still get hit with a fine.   When you realise how quickly everything turns from "Wee, we're having fun!" To "oh f**k oh f**k oh f**k", you start to realise the only way to be a good driver, is to not be doing anything dumb or unexpected by normies on the road. You want to go fast, go to the track. Someone there in a 1990s slow POS will also show you how bad of a driver you are as they lap 10 seconds per lap quicker than you can in a car that should be considerably faster.
×
×
  • Create New...