Jump to content
SAU Community

Recommended Posts

Hi All,

Found an old post you commented on from 2006

"On Skylines the spindles (vertical suspension arms) can and do bend. If so the easiest (best) method of fixing it is to replace the thing. Don't bodge the thing up - fix whats wrong."

Is there a easy way to tell this has bent if not visually (tried to measure same points on the other side but was the same and im not sure I am doing it correctly).

Long story - had my car in for alignment (they ended up running out of time so they just took my measurements). 
Anyway my front left KingPin Angle is out (its 10 degrees vs 17 on the right) with 5 castor. 

Cannot for the life of me figure out what is up with it, the adjustable camber arms are both set to the exact same length and the lower control arm seems fine (measures 315mm hole to hole same as the drivers side)

 

Alignment looks like

Front

Toe L-2 R-2

Camber L-1.35 R-1.33

Caster L5.44 R 5.22

Kingpin L 10 degrees R 17 degrees

Could be the upright is bent, but that's not really a common problem.

Could be bent/moved subframe. Could be the whole car is bent, having had a front ender and not put back straight.

I would suggest taking it to the sort of chassis shop that crash repairers use when they can't get  car straight again. If you were in SA I would suggest someone to look at it. Can't do that for anyone else.

You'll never work this shit out for yourself. You don't have the kit for making these sorts of measurements.

Thanks GTSboy, appreciate the input I think that will be the best route to take.

It hasnt had a hit in my 13 years of ownership and the kingpin angle was fine (11/12) when I had it aligned 3 years back now

Ill track down a shop in Vic to get it measured up for the subframe  and all

On 04/11/2021 at 2:59 PM, will34 said:

Thanks GTSboy, appreciate the input I think that will be the best route to take.

It hasnt had a hit in my 13 years of ownership and the kingpin angle was fine (11/12) when I had it aligned 3 years back now

Ill track down a shop in Vic to get it measured up for the subframe  and all

Try R Kent and sons in Clayton north. They'll be able to work it out for you.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
×
×
  • Create New...