Jump to content
SAU Community

Recommended Posts

On 11/28/2021 at 12:07 PM, SLIXK said:

Stock turbo with no boost solenoid and stock ecu 

If the car is overboosting it will hit an R&R corner of the map. The calibration engineers set up the map so that as you exceed the load expected by the stock turbo the engine will run noticeably rich and pull ignition timing. I believe there is also protection if you exceed the airflow the MAFs can read.

  • Confused 1
Link to comment
https://www.sau.com.au/forums/topic/483045-high-end-burble/#findComment-7958181
Share on other sites

On 11/29/2021 at 10:37 AM, joshuaho96 said:

If the car is overboosting it will hit an R&R corner of the map. The calibration engineers set up the map so that as you exceed the load expected by the stock turbo the engine will run noticeably rich and pull ignition timing. I believe there is also protection if you exceed the airflow the MAFs can read.

How am I over boosting with just a 3 inch exhaust 

Link to comment
https://www.sau.com.au/forums/topic/483045-high-end-burble/#findComment-7958182
Share on other sites

On 11/29/2021 at 8:30 AM, SLIXK said:

How am I over boosting with just a 3 inch exhaust

Consider it to mean "more boost than the factory ECU tune is happy with". It is exactly as Joshua said. The high load high rpm corner of the factory maps are both grossly rich and very retarded. If your bigger exhaust is allowing a little more gas to flow, you will go deeper into that region and experience more of it.

Link to comment
https://www.sau.com.au/forums/topic/483045-high-end-burble/#findComment-7958185
Share on other sites

On 11/28/2021 at 2:00 PM, SLIXK said:

How am I over boosting with just a 3 inch exhaust 

If you have a Nistune you can read the TP load index, if you're hitting 88 that means you've reached the limits of the stock map. Maybe you have a very high RPM/load misfire that is going to get worse but it could also be that you need a slight remap.

Link to comment
https://www.sau.com.au/forums/topic/483045-high-end-burble/#findComment-7958187
Share on other sites

On 11/29/2021 at 11:52 AM, joshuaho96 said:

If you have a Nistune you can read the TP load index, if you're hitting 88 that means you've reached the limits of the stock map. Maybe you have a very high RPM/load misfire that is going to get worse but it could also be that you need a slight remap.

Can my stock auto ecu be remapped?

 

On 11/29/2021 at 11:43 AM, GTSBoy said:

Consider it to mean "more boost than the factory ECU tune is happy with". It is exactly as Joshua said. The high load high rpm corner of the factory maps are both grossly rich and very retarded. If your bigger exhaust is allowing a little more gas to flow, you will go deeper into that region and experience more of it.

So basically I need a tunable ecu ?

Link to comment
https://www.sau.com.au/forums/topic/483045-high-end-burble/#findComment-7958188
Share on other sites

On 11/28/2021 at 3:09 PM, SLIXK said:

Can my stock auto ecu be remapped?

 

So basically I need a tunable ecu ?

I forgot which section of the forum I'm in. If you have a WC34 S2 with a JECS ECU then it can be remapped with Nistune. Load index maxing out at 88 is an RB26 thing, not RB25.

Link to comment
https://www.sau.com.au/forums/topic/483045-high-end-burble/#findComment-7958189
Share on other sites

On 11/29/2021 at 12:14 PM, joshuaho96 said:

I forgot which section of the forum I'm in. If you have a WC34 S2 with a JECS ECU then it can be remapped with Nistune. Load index maxing out at 88 is an RB26 thing, not RB25.

If I go with nistune am I able to change my ecu to a link at a later stage or is the nistune a permanent mod?

Link to comment
https://www.sau.com.au/forums/topic/483045-high-end-burble/#findComment-7958193
Share on other sites

On 11/28/2021 at 4:07 PM, SLIXK said:

If I go with nistune am I able to change my ecu to a link at a later stage or is the nistune a permanent mod?

The Nistune is a daughterboard that attaches to the OEM board. The Nistune Type 4 WC34 JECS board uses your OEM Consult port to connect to a tuner's laptop rather than cutting a hole in the ECU case for a USB port. So it is a fully reversible mod, especially when it comes to changing your ECU out for a Link standalone. There is no point in bothering to revert your ECU back to factory condition once you get a Nistune installed though, if you want the factory ECU map you can just flash it at any time and it will work just like factory. The only difference is unlike the OEM ECU you can see even more live diagnostic data. You will lose some conformal coating on the OEM ECU board in order to get to the solder joints so don't drop water on your ECU for any reason after that unless you apply new coating.

Tuning Nistune requires a different approach to how you would tune something like a Link, both because you're dealing with what is effectively compiled code (how the ECU does the math) and because the ECU uses MAF primarily as the load scaler. Most people are unfamiliar with how MAFs work.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/483045-high-end-burble/#findComment-7958200
Share on other sites

On 11/29/2021 at 2:51 PM, joshuaho96 said:

The Nistune is a daughterboard that attaches to the OEM board. The Nistune Type 4 WC34 JECS board uses your OEM Consult port to connect to a tuner's laptop rather than cutting a hole in the ECU case for a USB port. So it is a fully reversible mod, especially when it comes to changing your ECU out for a Link standalone. There is no point in bothering to revert your ECU back to factory condition once you get a Nistune installed though, if you want the factory ECU map you can just flash it at any time and it will work just like factory. The only difference is unlike the OEM ECU you can see even more live diagnostic data. You will lose some conformal coating on the OEM ECU board in order to get to the solder joints so don't drop water on your ECU for any reason after that unless you apply new coating.

Tuning Nistune requires a different approach to how you would tune something like a Link, both because you're dealing with what is effectively compiled code (how the ECU does the math) and because the ECU uses MAF primarily as the load scaler. Most people are unfamiliar with how MAFs work.

 Sweet so my auto ecu will be taken out for a stand alone like link so I don’t need to worry about reverting the nistune ?

Link to comment
https://www.sau.com.au/forums/topic/483045-high-end-burble/#findComment-7958206
Share on other sites

On 11/29/2021 at 5:31 PM, SLIXK said:

 Sweet so my auto ecu will be taken out for a stand alone like link so I don’t need to worry about reverting the nistune ?

 

On 11/29/2021 at 2:51 PM, joshuaho96 said:

The Nistune is a daughterboard that attaches to the OEM board. The Nistune Type 4 WC34 JECS board uses your OEM Consult port to connect to a tuner's laptop rather than cutting a hole in the ECU case for a USB port. So it is a fully reversible mod, especially when it comes to changing your ECU out for a Link standalone. There is no point in bothering to revert your ECU back to factory condition once you get a Nistune installed though, if you want the factory ECU map you can just flash it at any time and it will work just like factory. The only difference is unlike the OEM ECU you can see even more live diagnostic data. You will lose some conformal coating on the OEM ECU board in order to get to the solder joints so don't drop water on your ECU for any reason after that unless you apply new coating.

Tuning Nistune requires a different approach to how you would tune something like a Link, both because you're dealing with what is effectively compiled code (how the ECU does the math) and because the ECU uses MAF primarily as the load scaler. Most people are unfamiliar with how MAFs work.

When I upgrade to link that is hah

Link to comment
https://www.sau.com.au/forums/topic/483045-high-end-burble/#findComment-7958207
Share on other sites

On 11/28/2021 at 6:35 PM, GTSBoy said:

Hardly. Load is load.

You have a point there, but the finer points of how the sensors work tends to be a reason why tuners don't like MAF-based tuning. The old hot wire sensors will see weird behavior in transients that requires min/max clamping. Card style hot film is better about reversion but the other issues still apply. There's also all the fun stuff that comes with MAFs on heavily modified intakes, usually OEM engineers sweat those details so there aren't weird issues causing a lot of noise in the MAF signal, etc...

I've talked to a number of tuners and even Haltech USA tells me nobody seems to care about MAF support in their ECUs, so they don't really have a lot of experience there. Link support will also say similar things, their near-universal advice is run speed density on their ECUs because tuners don't really use the MAF support so they don't put much effort into maintaining it properly.

Personally I don't care, if the factory setup is MAF and after thinking hard on the tradeoffs MAFs still make sense then I'll do whatever it takes to make it run properly, but I don't think that's how most tuners operate.

On 11/28/2021 at 8:31 PM, SLIXK said:

 Sweet so my auto ecu will be taken out for a stand alone like link so I don’t need to worry about reverting the nistune ?

Yes, there's no need to revert a Nistune mod. Personally I would keep it even after switching to a Link as a diagnostic tool while developing a base map properly.

Edited by joshuaho96
Link to comment
https://www.sau.com.au/forums/topic/483045-high-end-burble/#findComment-7958208
Share on other sites

On 11/29/2021 at 4:47 PM, joshuaho96 said:

Personally I don't care, if the factory setup is MAF and after thinking hard on the tradeoffs MAFs still make sense then I'll do whatever it takes to make it run properly, but I don't think that's how most tuners operate.

Once you're into "the AFM is suffering from reversion, etc" territory, it's time to slip the card type AFM into the cooler pipework and just sidestep all that old bullshit. We're >10 years into the new world of possibilities offered by the new AFMs.

Link to comment
https://www.sau.com.au/forums/topic/483045-high-end-burble/#findComment-7958209
Share on other sites

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...