Jump to content
SAU Community

R33 gtst where does this trunk wire go?

Templim

By Templim,
in R Series (R30, R31, R32, R33, R34)

 Share

Recommended Posts

GTSBoy Grand Master

GTSBoy

Posted
Posted
2 hours ago, joshuaho96 said:

Pretty sure there's no lock solenoid on the R33 for the trunk, just the cable and the key bellcrank hitting the latch. It's either for a brake light or the switch that activates the trunk light.

Yuh, so both the solenoid and the bootlid stop light would have been aftermarket additions, not factory, hence my reference to an assumption of not being able to find it on the wiring diagram. Wiring diagram being the first port of call for answering these questions.

And....is the switch for the boot light not adjacent the hinge, and not down in the "slam violently" zone near the latch? The wiring for a switch near the hinge would also be shorter and more efficient than unnecessarily locating it at the latch.

Duncan Grand Master

Duncan

Posted
Posted

It looks like a factory plug, has to be for a spoiler mounted brake light. You can check with a multimeter or test light, you should get 12v between them with the brake pressed (and not otherwise)

joshuaho96 Veteran

joshuaho96

Posted
Posted
26 minutes ago, GTSBoy said:

Yuh, so both the solenoid and the bootlid stop light would have been aftermarket additions, not factory, hence my reference to an assumption of not being able to find it on the wiring diagram. Wiring diagram being the first port of call for answering these questions.

And....is the switch for the boot light not adjacent the hinge, and not down in the "slam violently" zone near the latch? The wiring for a switch near the hinge would also be shorter and more efficient than unnecessarily locating it at the latch.

I'd have to check again but I'm pretty sure the light switch is in the trunk lid. Why that is I couldn't tell you.

GTSBoy Grand Master

GTSBoy

Posted
Posted

Hmm. You might be right. I just looked on mine (32, not 33). I have some sort of a little magnetic switch (or something ish) attached to the latch in the lid with a red/black pair, and in the same loom there's a brown/black pair with a 2 pin connector, not attached to anything. It's near the latch, not halfway up the boot lid frame like the OP's photo. It's strange. I've always known that that loom was strapped to the boot frame, yet always assumed that the light switch was near the light itself / the hinge.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      33 GTR Broken front wheel knuckle

      By GTSBoy · Posted

      There's plenty of OEM steering arms that are bolted on. Not in the same fashion/orientation as that one, to be sure, but still. Examples of what I'm thinking of would use holes like the ones that have the downward facing studs on the GTR uprights (down the bottom end, under the driveshaft opening, near the lower balljoint) and bolt a steering arm on using only 2 bolts that would be somewhat similarly in shear as these you're complainig about. I reckon old Holdens did that, and I've never seen a broken one of those.
    • MBS206
      33 GTR Broken front wheel knuckle

      By MBS206 · Posted

      Let's be honest, most of the people designing parts like the above, aren't engineers. Sometimes they come from disciplines that gives them more qualitative feel for design than quantitive, however, plenty of them have just picked up a license to Fusion and started making things. And that's the honest part about the majority of these guys making parts like that, they don't have huge R&D teams and heaps of time or experience working out the numbers on it. Shit, most smaller teams that do have real engineers still roll with "yeah, it should be okay, and does the job, let's make them and just see"...   The smaller guys like KiwiCNC, aren't the likes of Bosch etc with proper engineering procedures, and oversights, and sign off. As such, it's why they can produce a product to market a lot quicker, but it always comes back to, question it all.   I'm still not a fan of that bolt on piece. Why not just machine it all in one go? With the right design it's possible. The only reason I can see is if they want different heights/length for the tie rod to bolt to. And if they have the cncs themselves,they can easily offer that exact feature, and just machine it all in one go. 
    • Bennym35
      New guy

      By Bennym35 · Posted

      The roof is wrapped
    • Duncan
      R34 GT-T cycling ABS pump

      By Duncan · Posted

      This is how I last did this when I had a master cylinder fail and introduce air. Bleed before first stage, go oh shit through first stage, bleed at end of first stage, go oh shit through second stage, bleed at end of second stage, go oh shit through third stage, bleed at end of third stage, go oh shit through fourth stage, bleed at lunch, go oh shit through fifth stage, bleed at end of fifth stage, go oh shit through sixth stage....you get the idea. It did come good in the end. My Topdon scan tool can bleed the HY51 and V37, but it doesn't have a consult connector and I don't have an R34 to check that on. I think finding a tool in an Australian workshop other than Nissan that can bleed an R34 will be like rocking horse poo. No way will a generic ODB tool do it.
    • GTSBoy
      33 GTR Broken front wheel knuckle

      By GTSBoy · Posted

      Hmm. Perhaps not the same engineers. The OE Nissan engineers did not forsee a future with spacers pushing the tie rod force application further away from the steering arm and creating that torque. The failures are happening since the advent of those things, and some 30 years after they designed the uprights. So latent casting deficiencies, 30+ yrs of wear and tear, + unexpected usage could quite easily = unforeseen failure. Meanwhile, the engineers who are designing the billet CNC or fabricated uprights are also designing, for the same parts makers, the correction tie rod ends. And they are designing and building these with motorsport (or, at the very least, the meth addled antics of drifters) in mind. So I would hope (in fact, I would expect) that their design work included the offset of that steering force. Doesn't mean that it is not totally valid to ask the question of them, before committing $$.
×
×
  • Create New...