Jump to content
SAU Community

Recommended Posts

  • 4 weeks later...

So today I went well outside my comfort zone (again) to replace my valve cover gasket. 

I have had a big leak over the exhaust leading to a lot of smoke and smell every time I drove it. The leak was in the rear driver's corner. 

The job wasn't hard as such, just a bit finicky and time consuming. 

The old gasket was rock hard and broken right where the leak was. 

PXL_20240609_043007537.jpg

The leaky corner had so much sitting oil in it. 

PXL_20240609_042851779.jpg

The good news to my amateur eyes was no buildup or sludge under the cover. It all looked fairly nice in there.

PXL_20240609_042827882.jpg

 

I haven't started it yet. I ran out of light and body when putting the coils and injector loom back in. Probs only 30min left for the morning. 

I was so nervous putting the cover back on, I must have lifted it 5 times to make sure the gasket was still seated properly.

God it's going to be nice to be leak free and not make other traffic light queuers think my car is about to explode.

  • Like 4

My happiness was short lived. 

The car has a violently rough idle. If I get the revs up it runs really nicely albeit with some very small misses occasionally.

I have checked and double checked all my connections and vacuum lines. I've even replaced some unrelated vacuum lines to to and find the problem. 

The codes are all over the place. Throttle position, throttle vacuum, o2 sensor 1, o2 sensor 2, occasional misfire code. Makes me think a wire has been broken or something isn't clipped in properly but there's so little around where I was working to miss plugging in or to break. Super weird. 

It's only at warm idle. Cold start is beautiful until the revs drop below 850 - 900 rpm then all hell breaks loose.

  • Sad 2
1 hour ago, PranK said:

My happiness was short lived. 

The car has a violently rough idle. If I get the revs up it runs really nicely albeit with some very small misses occasionally.

I have checked and double checked all my connections and vacuum lines. I've even replaced some unrelated vacuum lines to to and find the problem. 

The codes are all over the place. Throttle position, throttle vacuum, o2 sensor 1, o2 sensor 2, occasional misfire code. Makes me think a wire has been broken or something isn't clipped in properly but there's so little around where I was working to miss plugging in or to break. Super weird. 

It's only at warm idle. Cold start is beautiful until the revs drop below 850 - 900 rpm then all hell breaks loose.

Did you disconnect the battery for a while?

It might need to relearn how to BMW, maybe?????

  • Like 1
41 minutes ago, The Bogan said:

Did you disconnect the battery for a while?

It might need to relearn how to BMW, maybe?????

Yep battery was off the whole time. I did have to reset about 1000 "adaptations" in the various ecus but no love. 

I might pull the throttle body out and give it a clean but I'm not convinced.

I don't get why it runs fine at higher revs. The cold start today was beautiful! 

1 hour ago, PranK said:

Yep battery was off the whole time. I did have to reset about 1000 "adaptations" in the various ecus but no love. 

I might pull the throttle body out and give it a clean but I'm not convinced.

I don't get why it runs fine at higher revs. The cold start today was beautiful! 

Does it have a vacuum brake booster?

If it does, and the booster isn't connected you will get TPS and all sorts of other codes, and it will struggle to idle

Have you driven the car, checked the brakes?

  • Like 1
2 hours ago, The Bogan said:

Does it have a vacuum brake booster?

If it does, and the booster isn't connected you will get TPS and all sorts of other codes, and it will struggle to idle

Have you driven the car, checked the brakes?

I have driven it slowly around the block, didn't notice any issue with the brakes. It is a vacuum brake booster.

  • Sad 1

So, after going through everything multiple times and even cleaning plugs with contact cleaner, I am making no inroads at all. 

I found one post from a dude who had a little pinch in his gasket and so I'm convinced it has to be a loss of vacuum caused by this. So, I'll take it all off (it'll be much quicker this time) and inspect and reseat the gasket. Its a genuine BMW rubber gasket, hopefully theres no damage. 

Also, as the valve cover is plastic they can crack. Mine inspected ok last time but I'll have an extra close look this time.

Thank god I work from home. Can't believe the X5 has gone out in sympathy though. It needs a new front diff or diff rebuild. 

🤞

Found the problem. I cracked part of the valve cover when trying to pry it off. Theres a big leak there.

I did see this when I did it but the part that I cracked looked like it was just for mounting the fuel rail on and not for vacuum. After asking on Reddit, it appears that part is 100% pcv related.

I'm slightly irritated at having to swap it out for a third time but also super happy to have found the problem. I can fix and move on.

More fuel for you N54 haters, the valve covers are plastic. :)

 

  • Like 1
17 hours ago, PranK said:

Found the problem. I cracked part of the valve cover when trying to pry it off. Theres a big leak there.

I did see this when I did it but the part that I cracked looked like it was just for mounting the fuel rail on and not for vacuum. After asking on Reddit, it appears that part is 100% pcv related.

I'm slightly irritated at having to swap it out for a third time but also super happy to have found the problem. I can fix and move on.

More fuel for you N54 haters, the valve covers are plastic. :)

 

I was going to say generally speaking if it's like 80k+ miles since the valve cover has been replaced you don't even attempt to just replace the gasket. The valve cover itself will likely be warped and it will continue to leak after replacement, just not as severely. The valve cover PCV diaphragm can also tear and create a major vacuum leak.

Welcome to BMW life. My friend's 2006 330i was t-boned and totaled out so he also just got a 335i so I can add to this thread now.

Edited by joshuaho96
4 hours ago, joshuaho96 said:

I was going to say generally speaking if it's like 80k+ miles since the valve cover has been replaced you don't even attempt to just replace the gasket. The valve cover itself will likely be warped and it will continue to leak after replacement, just not as severely. The valve cover PCV diaphragm can also tear and create a major vacuum leak.

Welcome to BMW life. My friend's 2006 330i was t-boned and totaled out so he also just got a 335i so I can add to this thread now.

I must have read 100 DIY's and watched 200 DIY Youtube videos with most people saying just grab a new cover and, well, despite my normal aproach to these things (replace it all!!) I didn't get a cover. I don't know why I didn't, I'd already ordered a bunch of bits from FCP and it would have made perfect sense to put that in the order. 

Anyway, I'm not getting OEM as its just crazy money, even from the states its 900 ish delivered. So, I got an OE Elring one, same as they sell at FCP but local so I can get this fixed this week. Our X5 is waiting for a new diff so we find ourselves in a common scenario of having 2 broken BMW's on the driveway! 🤣

We're back! 

The new valve cover arrived on Friday and I fitted it Friday night and in the rain on Saturday. 

The car runs perfectly! Also as it gets through the residual oil there's less smoke which is really nice. Hopefully that's all gone after an hour long drive today. Anxious me will go around the whole cover tomorrow with a mirror and torch to make sure gasket is where it should be and that oil is also where it should be.

It was a much tighter fit! As you'd expect and I did the torque sequence twice as it kind of settled into place. I might go around it again just to be sure.

  • Like 3

Ok, so here the embarrassing 'fess up' post.

Here's the crack, or broken part of the old valve cover.

image.jpeg

Pretty obvious break and in hindsight it's quite the face palmer 🤦‍♂️ but let me explain why I didn't think this was a problem.

This side part of the valve cover is an additional piece, it protrudes from the main valve cover and it's also where the fuel rail mounts..... 

image.png

You can see the rail at the bottom and you can see this external piece hanging off the side of the cover. It almost looks sandwiched in this pic. 

Here's another cover with that side piece ... 

image.png

On top of this, when looking at the inside of the cover, there were no openings(*) for that section.

image.jpeg

So I really just thought I'd broken some crispy plastic mount for the fuel rail.... Until somebody drew my attention to the air openings at the BOTTOM of the cover, not INSIDE the cover. So, I had a ginormous PCV leak.

The cover needed to go and I should have taken everybodies advice and got a new one in the first place. The original one is just fried, its really brittle. It was nice to have the new one be really snug in position and the screws were slightly tight to do up which was completely different to the original ones that almost undid themselves.

 

 

  • Like 1

So, some plans for the old girl...

  • Blackline LSD - Given the cost, its doable over the RacingDiffs LSD conversion. I can get it landed for about $1200. Currently I'm the only car in the family that can't get up Bec's mum's crazy steep and slippery driveway. All other cars are fine but I sit spinning one wheel. :(  How embarrassment. 
  • An exhaust - I'm not sure what I want here but something just cat back as I can't hear my exhaust at all from inside the car and I need to constantly check tach on the track to see if my shift was accepted (gearbox wont allow high rev downshifts and I need to check the gear or tach a lot to make sure it went through because I can't hear it).
  • Either solid aluminium or super hard poly rear subframe bushings - The back squirms a lot at the moment, if I give it anything at all on a slight turn or on unhappy surface it just moves around too much. Apparently very little nvh with the aluminium bushings but these can damage the underside because they dont give anything. A little undecided.
  • I got a replacement headlight for my 'fish tank' headlight. I'll sand both headlights back and clear coat them. I've found this is the best way to restore horrible BMW headlight covers.
  • Rear adjustable camber arms - I'd like to be able to dial a little bit of camber in on the rear.
  • I would still like a cheap fixed seat to swap in for the track. I flop around everywhere in the stock seats despite them being the M Sport seats.
  • I'll need to change my oil filter housing gasket soon as I think I have a small leak.
  • I'd like to check the condition of my intake/valves because the direct injection doesn't clean them up and if theres buildup I'd like to clean them. Tho, I don't see this as much of a common issue in AU over the US. I'm not sure why.

Thats all I can think of. 

 

I forgot this from last month. A small one but made a difference to me. 

My gear knob and boot was just so gross. I hated looking at them. 

image.png

I really wanted a genuine BMW Performance knob and boot but they came in around $500 or so which is just stupid. So for months I watched eBay and found a dude selling a set from the states for about $200 delivered. 

I had to perform minor surgery on the boot as LHD is different but I got it to fit and it looks so much nicer.

image.png

I love them. As much as I can love an auto shifter at least 🤣

Now the surround looks gross. I guess I'll just keep going until the grossness is all eliminated! 

  • Like 2

Did a bit of a repair on my headlights over the weekend.

The drivers side headlight turns into a swimming pool every time it rains, so I bought a replacement. Got a bargain at $380 with the next cheapest being $550. I had to swap my angel eyes bulb, Xenon, high beam flasher and indicator over from the old light and once I opened the new one it was just so full of sand and shit everywhere I reckon it was a Simpson Desert recover vehicle or something. It was terrible and I now know why it was cheap.

Anyway, after swapping my main bulbs over I thought I'd clean up the install of the angel eyes bulbs in both drivers and passengers headlights. The wiring in the headlight is just cracking so badly and rather than pull it out to replace it, I just fed some heat shrink down over the cracked parts to protect it. Also cleaned up some joins.

PXL_20240630_040303228.jpg

PXL_20240630_040314428.MP.jpg

PXL_20240630_042140966.jpg

PXL_20240630_042806614.jpg

The factory pre LCI angel eyes are like an orange/brown and are hideous.

I also wet sanded and clear coated the headlights but it was probably too cold. They're better than they were but not great still so I'll have another go shortly as I can do this on the car.

I also had to replace the adaptive controller on the new headlight, the last one had clearly been very wet and was filled with sand. I had a replacement one here as they are not exactly reliable. 

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...