Jump to content
SAU Community

Recommended Posts

Mine stopped working about 6 months ago, I took it out, took it apart and found a bad solder joint.  I re-soldered that and a few other higher stress joints and put it back it, it has been working fine since.

Can't guarantee yours has the same fault though.

  • Like 1

:)  that is the fun part.. you can unplug the lamp from underneath the parcel shelf (access from the boot).  However, you need to remove the rear seat, so you can remove the parcel shelf, the lamp is attached to the bottom of the parcel shelf.

Maybe try having someone hold their foot on the brake pedal and ensure the normal side brake lights are on, then, push and flex the cable to the lamp (from the boot side) and see if the light turns on and off.  If it does, a bad solder joint is probably the issue and you will need to remove it to repair it.

2 hours ago, doggido said:

Checked out the above website and it looks promising so I will give it a go over the weekend.

So then, it leaves me one question, where does the red come from?

I dont have a direct answer, however, many years ago when I first got my 350GT Coupe, I replaced the front orange indicators with clear lenses. It failed the pink slip, but my mechanics didn't skip a beat, and put in orange caps inside the clear lensed indicators, and passed it without question. I guess what I am saying is, just try asking your regular mechanic. My guys didn't even check with me before doing it, they just told me when I went to pick it up.

If you want a selfie, maybe go to wreckers and find a broken red plastic taillight, and cut it to fit & cover the globes; or even a smaller upper taillight from a different car. Maybe even heat it a little to conform to a shape. Just spit-balling

Yeah, well, what's worse is that the DIY link above used RGB LEDs driven to make white. They could have made red. Maybe not as bright, but then winding up the brightness by going white and then filtering down to red with the red plastic diffuser is probably going to have the same effect.

 

As I was doing the rounds of the local wreckers, I found one that had a V35 in the yard which they haven't stripped yet. I grabbed the brake light out of it and got them to test which all LEDs worked. I ended up getting it for $60NZD. As long as I can at least a couple of years out of it I'll be happy.

  • Like 3

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...