Jump to content
SAU Community

Driling oil feed in 23U AWD block?

JarrettL

By JarrettL,
in Engines & Forced Induction

 Share

Recommended Posts

JarrettL Contributor

JarrettL

Posted
Posted

Alright, I've held off from posting this because it doesn't seem to make any sense and I know it's a topic that was beat to death and back two decades ago and then again after that.

I have an AWD 23U block from an ENR34 that was NA from the factory. I'm rebuilding it with a turbo NEO head and ARP studs to sell it on so I can move on to a different engine build, and I'm stumped on the oil feed. Conventional logic, as I understand it, is that the NA blocks are tapped for the oil feed from the factory, but don't drilled through into the passage. This block seems to have a small hole withing the M12 threaded hole that goes fairly deep into the block material. So it would seem at a glance to be done in this application. Only, this engine has never been turbocharged, and I didn't remove a plug from this hole when tearing it down. Does the hole need to go even further than the depth I've shown here with the drill bit? Am I missing something?

PXL_20230325_222022189.jpg

PXL_20230325_222030450.jpg

PXL_20230325_222148334.jpg

Link to comment
https://www.sau.com.au/forums/topic/484554-driling-oil-feed-in-23u-awd-block/
Share on other sites
Duncan Grand Master

Duncan

Posted
Posted
2 hours ago, FiXtUrE said:

Measure the hole from which welch plug you’re going to remove/tap into. Earls fittings will braided lines should do the job, depending on the hole size.

I don't think that is good advice, if you attach a turbo oil feed to a welch plug you will get coolant, not oil in most cases.

In this case the oil feed seems to be there, it is just a question of making sure is connected right through.

  • Thanks 1
Duncan Grand Master

Duncan

Posted
Posted
9 minutes ago, FiXtUrE said:

What remove Welch plug, add helicoil ( which will shorten/lower the thread size though for the fitting ) Otherwise tap a thread into the existing hole.

Mate, I don't know what is going on with your posts, but I can only think one 1 welch plug in an rb that goes to an oil gallery and it is not externally accessible (behind the oil pump). There is another in the rear of the head but it is to a void not a pressure source. 

Please post a pic with exactly which welch plug you think would be suitable for use as a turbo oil feed.

To OP, I don't have a disassembled block handy, but I believe the oil galleries are on the right side of the block, so yes it could be a pretty long passage. It looks like your sump is off so spin it over and have a look

Duncan Grand Master

Duncan

Posted
Posted

I know the smart choice is to let this go, but FYI those welch plugs go to the water jacket and have coolant behind them, so would not be great as a turbo oil feed. OP is holding a drill, not pointing at the welch plug. Per their first pic, they are asking about the factory threaded hole in the block between cylinders 3 and 4

GTSBoy Grand Master

GTSBoy

Posted
Posted
15 minutes ago, NZ-GTT said:

You may want to add another fool to your ignore list!

Considered it! It seems that our rocket surgeon has taken himself off to be an expert on Aliexpress lip extensions and body kit bullshit, in a part of the forum that I never visit. He hasn't been seen in the useful part of the forum for a week or so.

TurboTapin Experienced

TurboTapin

Posted
Posted
4 hours ago, GTSBoy said:

Considered it! It seems that our rocket surgeon has taken himself off to be an expert on Aliexpress lip extensions and body kit bullshit, in a part of the forum that I never visit. He hasn't been seen in the useful part of the forum for a week or so.

FiXtUrE after reading your comment.

image.thumb.jpeg.e6372facc3be052ac36d294ccd2646fe.jpeg

 

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Chupapy
      Coolant leak?

      By Chupapy · Posted

      Is it alright to top up with just another green coolant?
    • Songo
      New kid on the block

      By Songo · Posted

      thanks GTSboy. My confusion at the moment is i am trying to locate the ignition, ECU battery power and the ECU negative The closest thing i can find is the for the S15 on Page 8 of the Wiring Specialties web page https://drive.google.com/file/d/0B9F33_M_GgENQnZ6STMxVmVNd1E/view?resourcekey=0-eZ4nNRwRoqa1qvKlWWHm8A I cannot find the same diagram for the R33 RB25DET Series 2 dash plug pin out.... Do you know what the Pins? or know where i can find the same pinout diagram for the RB dash plug? Thanks for the advice on the box... i like a 6 speed so might be on the lookout or the box now.. a topic of discussion for another post...
    • Chupapy
      Coolant leak?

      By Chupapy · Posted

      Will have a look at that. I cant see any leaks 
    • GTSBoy
      Coolant leak?

      By GTSBoy · Posted

      Put another overflow bottle (ie, a 1.25 coke bottle or similar) under the overflow hose and see if it is being pushed out there or if it is disappearing into the engine.
    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      Staring on a stand is no issue. You just have to wire everything up, give it fuel and cross your fingers that the stand is robust enough. Arranging the inlet plumbing is often the hardest part, without any surrounding structure to hand some of it from. No need for coolant if you only want to run it for <1 minute. As to the gearbox - I think the little Aisin box is a bit stronger than the other small Nissan boxes that went behind SRs, but I wouldn't be too keen to test its limits with the torque of a boosted 25. I don't know if you can retain the box and the tailshaft. The box won't connect to the RB without an adapter of some sort, which is either a plate that will push the engine forward (which is not good for fitting it into the bay's available space) or push the box back, which messes with the box position and tailshaft length - OR - cut and shut work on the bellhousing, which is a long way from "least modification". I'd be buying a new 370Z 6 speed or similar, doing what has to be done to that to make it fit RB (ie, cut and shut bellhousing) and the requisite tailshaft custom/mods.
×
×
  • Create New...