Jump to content
SAU Community

Recommended Posts

So I have been watching some of the video's peddling these and on paper they look like magic. 

I have a r34 getrag with a nismo supercoppermix  and its amazing to drive, just holds the power but the box is noisy and I would like a little more room power wise. 

 

So the claim is with the new dampening design in the Uniclutch I will get "near" factory levels of gearbox noise without the dual mass flywheel. 

The torque ratings are very high so power seems like no issue, 800ft/lb will be near 1000hp on an rb26.  

 

So the only question I have is pedal weight,  it will be going from pull to push.  I have an injury that means an overly heavy pedal will not be do-able. 

 

Any one used one yet ? 

Edited by Butters
  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/485172-uniclutch/
Share on other sites

From what they say, the pedal weight should be less than most comparably rated clutches. So.... perhaps you shouldn't worry? The lower end of their range is supposed to be stock pedal weight or lighter, and the race end is supposed to be "surprisingly light", from what I gathered from (likely) the same vids.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/485172-uniclutch/#findComment-7985678
Share on other sites

Speaking to them over email at the moment, they did suggest the track model might be better for 1000hp which I imagine is covering themselves. 

 

Getting a straight answer on which flywheel to use is proving tricky, might be easier to just call them. 

 

Any recommendations on a pull to push conversion ?

Been looking at ORC and ATS but both state specific to their clutch. 

Link to comment
https://www.sau.com.au/forums/topic/485172-uniclutch/#findComment-7985706
Share on other sites

  • 5 months later...

Track version is now out for the GTR. 

Got this when i asked about track version still having RDC, which is good news. 

 

"All UniClutch’s have silent shift - even the track version. So never any chatter . Track has Quad drive noise dampening which has less angularity than dual drive RDC, but it’s stronger, and will still dampen noise in a Petrol vehicle without a dual mass flywheel . Would be a little noisier in a diesel if the DMF has been swapped out. But that is usually 4x4s and there is a 4Terrain UniClutch tuned for that type of vehicle - ie a Patrol.

 

Still no detail on which flywheel to use with the BNR34 nor a recommended pull to push conversion.  

Link to comment
https://www.sau.com.au/forums/topic/485172-uniclutch/#findComment-7990763
Share on other sites

From Uniclutch 

 

"For the flywheels, both the R32 and R34 GTR are very similar and share the same UniClutch fitment kit so you can purchase whichever you like. Just be aware that you would set it up according to the flywheel you buy. If using an R32 GTR flywheel, setup the UniClutch like an R32 GTR.

Yes, you will need a pull-to-push conversion. We are working on a pull type UniClutch, however, this is expected near the end of the year. The OS Giken stuff works great."

 

Trying to decide between these two flywheels - 

https://www.rhdjapan.com/nismo-lightweight-flywheel-for-sports-clutch-kit-bnr34.html

https://www.rhdjapan.com/nismo-lightweight-flywheel-for-sports-clutch-kit-bnr32-bcnr33-r32-r33-a31-wgnc34.html

 

Any others I should be looking at ?

 

 

...

 

 

Link to comment
https://www.sau.com.au/forums/topic/485172-uniclutch/#findComment-7990838
Share on other sites

would a NPC one work?

https://www.npcperformance.com.au/product/lightweight-billet-steel-flywheel-rnf03/

and here's their catalogue:

https://www.npcperformance.com.au/wp-content/uploads/2024/03/NPC-Performance-Flywheel-Catalogue-2023-Full-List-WEBSITE.pdf

(I am not affiliated, even though I keep recommending their shit lol... I am going to buy a Xtreme clutch soon)

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/485172-uniclutch/#findComment-7990839
Share on other sites

  • 1 month later...

Just some day one info. 

It is heavy, the flywheel being built in makes for a solid setup.  Will try and weigh with a flywheel to compare to a direct clutch or nismo twin.

Also the advertised torque is peak, which is not unsurprising and explains my previous conversations. So real torque is about 1000 FT/lB, plenty for a 1000hp GTR.  

Considering mine is making 600ft/lb wheels, 650-80 ish fly(?) lots of room for more power :)

 

image.thumb.png.847b7ca0d82e1ea419fb531300d9d21d.png

Link to comment
https://www.sau.com.au/forums/topic/485172-uniclutch/#findComment-7992193
Share on other sites

  • 1 month later...

Any updates?

Curious to know/hear/see experience on these clutches and if it's just all hype.

Other option is just to get a run of the mill Xtreme Twin Plate organic and enjoy life and not worry about complications.

 

My clutch is starting to do weird shit after 3x motors and 10+ years of abuse.

When you ride it, and try to park the shit box, it sounds like a munted horse after 10 cones.

Link to comment
https://www.sau.com.au/forums/topic/485172-uniclutch/#findComment-7993178
Share on other sites

  • 3 months later...

Not yet, might end up being easter now, didn't end up getting time off over xmas. 

 

I've been seeing some concerning things online now too. Lots of people with issues, could all be setup issues but the consequences in some cases are significant. 

 

All of the below are other peoples stories, not mine and are unverified. 

Seen 2 x broken adapter ring that destroyed the gearbox as it failed.  

They still do seem to have twin plate rattle despite claims of silent.

Several issues with it not holding power but some evidence of constant pressure on plate.

Setup issues with bite point.  

Lot of people after 2-4 weeks swapping back to another brand. 

 

On the positive side, I've seen a barra put down near 1000hp at the wheels and its held it. 

Also everyone seems to confirm the pedal is light. 

 

Does have me a little cautious and looking at ATS carbon clutches again .......

 

 

 

 

Link to comment
https://www.sau.com.au/forums/topic/485172-uniclutch/#findComment-7996132
Share on other sites

Do need to take it with a pinch of salt.

One of the adapter failures, they clearly had setup issues with the flywheel. 

One of the slipping ones I spoke to and it was pretty clear the throwout was riding, rather than fix, just swapped to a new clutch. 

 

These clutches are being put in anything from 5k offroad 4x4 beaters, GR yaris, 500hp commodores to 1200hp barra monsters. Bound to be some issues in some of them when they are not a simple bolt in affair due to the changes in height. 

 

There is a lot going on in this picture and unless I did the job myself no way to tell what really happened. 

image.thumb.png.1cb13da97ea72c54d77dd730bbb55f44.png

  • Sad 1
Link to comment
https://www.sau.com.au/forums/topic/485172-uniclutch/#findComment-7996137
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
    • Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
    • My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
×
×
  • Create New...