Jump to content
SAU Community

Recommended Posts

On 24/4/2024 at 11:06 AM, WMDC35 said:

It's most likely a 25, has vct and alloy cas, only 20 neo has vct but would have plastic cas 

Okay guess what I found the block print has RB25 on it stupid f**ks literally has orange over spray on it it has a VCT Drain…so that rules out a neo

On 24/4/2024 at 8:16 AM, Duncan said:

You might be able to find the engine number (if about it hasn't been painted over....) the prefix should be rb25 or rb20

Gave  a nice look has RB25 but had orange spray over it and block is stamped 

“JAPAN” 75T which I’ve searched and it’s an rb25det block and no igniter on coil pack soo am I safe to assume it’s a S2 RB25DET..with a RB26 Intake plenum? I’ll be going for a plazmaman or a diff intake plenum kit suited for an rb25det can that give me a headache? If I leave the 26 on? Can that be the reason it’s running shit I’m happy to pay $$ for information on building it properly with a nice aeroflow 6262 .84 T4 turbo (either 50mm wastegate or 2x44mm wastegate 🤷🏻‍♂️ I was planning on forging the rods / pistons / tomei valve springs , Cams , e85 / flex  respray the whole car and a Rocket Bunny kit and a nice set of coilovers, link ecu? Or are there better ones for cheaper that can handle what I want & I heard these motors are good stock to push 400-500hp? Unless I read wrong  (But the way these retards painted it I think it’s safer to build the motor ground up as I want to run the 5-600hp mark figure 

Re trying to identify what it might (or might not be) a bit better, can you post up some good clear pics of the plenum and where it is bolted to the throttles/intake manifold/whatever is there.

An rb26 inlet manifold does not bolt straight onto an rb25 head due to different port placement/shapes, so there is either some sort of adapter plate, or it is a 26 head 

5 hours ago, R32.RB said:

Can that be the reason it’s running shit

Most likely it's tuning related.

That plenum is fine, moving to a Plazmaman you won't notice much of a difference.

If you want supreme low down, better off with the stock intake manifold & plenum OR the Rajab top half.

A Precision or Turbosmart 6262 is too big for what you want, and big boost with Tomei Valve springs also a fail.

You can make 373kW on a stock motor with just head studs, sensible timing in the mid range and it will last for your intended purposes (won't last on the track for too long).

6 hours ago, Duncan said:

Re trying to identify what it might (or might not be) a bit better, can you post up some good clear pics of the plenum and where it is bolted to the throttles/intake manifold/whatever is there.

An rb26 inlet manifold does not bolt straight onto an rb25 head due to different port placement/shapes, so there is either some sort of adapter plate, or it is a 26 head 

To me it just looks like an rb25 Freddy plenum.

7 hours ago, Duncan said:

Re trying to identify what it might (or might not be) a bit better, can you post up some good clear pics of the plenum and where it is bolted to the throttles/intake manifold/whatever is there.

An rb26 inlet manifold does not bolt straight onto an rb25 head due to different port placement/shapes, so there is either some sort of adapter plate, or it is a 26 head 

https://postimg.cc/gallery/mLzg1Pm

8 hours ago, Duncan said:

Re trying to identify what it might (or might not be) a bit better, can you post up some good clear pics of the plenum and where it is bolted to the throttles/intake manifold/whatever is there.

An rb26 inlet manifold does not bolt straight onto an rb25 head due to different port placement/shapes, so there is either some sort of adapter plate, or it is a 26 head 

Yes I Was reading that up, some places are doing those adapter / weld on ones, and blitz ones are out of production im totally unsure but I have definitely just uploaded pics hope this helps thanks 

23 minutes ago, R32.RB said:

Is a Freddy a fake Greddy?

It is, and you do. Everything points at it being a series 2 non NEO rb25. Of course, unknown internals so you don't know how hard you can push the setup.  If you can get hold of a borescope you could check the top of the pistons for stock or aftermarket markings, but that still won't tell you want rods you have which is arguably more important for  higher power

  • Thanks 1
5 minutes ago, Duncan said:

It is, and you do. Everything points at it being a series 2 non NEO rb25. Of course, unknown internals so you don't know how hard you can push the setup.  If you can get hold of a borescope you could check the top of the pistons for stock or aftermarket markings, but that still won't tell you want rods you have which is arguably more important for  higher power

Yeah ofc, as the car sat for a while I have no problems just going to buy a whole new pistons , rods , cams etc 

6 minutes ago, Duncan said:

It is, and you do. Everything points at it being a series 2 non NEO rb25. Of course, unknown internals so you don't know how hard you can push the setup.  If you can get hold of a borescope you could check the top of the pistons for stock or aftermarket markings, but that still won't tell you want rods you have which is arguably more important for  higher power

Sorry when you mean I do, do you mean I’ve got a Freddy one?

55 minutes ago, R32.RB said:

Freddy one?

Fake GReddy = Freddy

 

  

1 hour ago, R32.RB said:

Yes I Was reading that up, some places are doing those adapter / weld on ones, and blitz ones are out of production im totally unsure but I have definitely just uploaded pics hope this helps thanks 

Don't waste your money, money better spent on good engine management, modern injectors, drive by wire (so you can delete all that cable throttle, idle control valve junk).

 

  • Like 1
6 minutes ago, Dose Pipe Sutututu said:

Fake GReddy = Freddy

 

  

Don't waste your money, money better spent on good engine management, modern injectors, drive by wire (so you can delete all that cable throttle, idle control valve junk).

 

No no no im

not going to buy that junk I was assuming that’s what’s on the motor I would love a forward facing plenum, maybe a plenum for rb25det and a 90mm throttle body

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...