Jump to content
SAU Community

Recommended Posts

Hi all,

I copped some flack on another thread because of my intention to do an RB conversion to my HR30 Paul Newman.

What are the thoughts on a sort of stock looking 3029cc L Series in my PNV.

All the purists accept that on a power upgrade?????

Link to comment
https://www.sau.com.au/forums/topic/49228-r30-purists/
Share on other sites

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

Grumpy old turd alert.

I'll give you my honest suggestion and that is to set your old shitter on fire. Can't say I own a classic? You don't know what I own you ignorant fool. I'd take a DR30 any day over that. HR30's were built for hitting kerbslike this

Link to comment
https://www.sau.com.au/forums/topic/49228-r30-purists/#findComment-984803
Share on other sites

Grumpy old turd alert.

I'll give you my honest suggestion and that is to set your old shitter on fire. Can't say I own a classic? You don't know what I own you ignorant fool. I'd take a DR30 any day over that. [pisstake]HR30's are only good for hitting kerbs like this.[/pisstake]

Link to comment
https://www.sau.com.au/forums/topic/49228-r30-purists/#findComment-984804
Share on other sites

Grumpy old turd alert.

I'll give you my honest suggestion and that is to set your old shitter on fire. Can't say I own a classic? You don't know what I own you ignorant fool. I'd take a DR30 any day over that. [pisstake]HR30's are only good for hitting kerbs like this.[/pisstake]

HR30 PNE is hardly a shitter its like the brock edition of a commo (sorry to have to use that foul language).

I own a few cars of which one is powered by an RB25DET and the other a modified L28E.. guess which ones more fun to drive? thats right the MR30!! that L series growl and the unadulterated power is insane, who cares if its only a 2 valve, single cam, non cross flow engine? they can still make power and are a very good engine... and i am sure Ghostriders intentions for the 3.1L are not going to be shabby.

Link to comment
https://www.sau.com.au/forums/topic/49228-r30-purists/#findComment-985051
Share on other sites

Dear oh dear,this thread got off to an angry start! ;)

Ghostrider,in anohter thread didn't you say you had just completed the built of an RB25/30?

If you've finished this engine,I'd say stick to your original plan and use it.Much more cost effective! :) I think it'd have to be more "street friendly" than an angry L too. Although a 3L L's big stroke could bring a T51R on boost nice and early! :D

Your car....it's up to you!

Link to comment
https://www.sau.com.au/forums/topic/49228-r30-purists/#findComment-985323
Share on other sites

go the rb, but dont modify any original parts....use 2nd hand xmembers to chop, or make new ones, that way you can return it to standard...on the other hand, unless its completely stock at the moment, ie orig motor and brakes and such, it doesnt matter what you do to it cos it is no longer original anyways...

hell i dont know i love the old L series too.....supercharged 3.1 litre Lseries......oh god yes!

Link to comment
https://www.sau.com.au/forums/topic/49228-r30-purists/#findComment-985437
Share on other sites

To RSX, Turbo of coarse, probably a T04R or the GT35/40 I bought for the RB. The problems I spoke of are currently under control, these alternative medicine guys can be brilliant.

OHR30T, Yes the RB is finished, but thought I might shelve it for a while, as the 3L L Series sounds awesome, just think, No engineers report needed, no cat, just get a blue slip and go, as by chance, it will still be carrying the L20A engine number. Let our RTA & police have fun with that.

Link to comment
https://www.sau.com.au/forums/topic/49228-r30-purists/#findComment-985595
Share on other sites

Grumpy old turd alert.

I'll give you my honest suggestion and that is to set your old shitter on fire. Can't say I own a classic? You don't know what I own you ignorant fool. I'd take a DR30 any day over that. [pisstake]HR30's are only good for hitting kerbs like this.[/pisstake]

What can I say?????

Listen to the masses, you appear to be out numbered in your views.

As you have the numbers covered, we won't know for sure, but as it has WA plates, DID YOU HAVE A BAD DAY AT THE DRIFTING???????

As for HR's on drift, maybe you should look at some of the R33's after they come unglued at the drift meets, even the japs have mishaps occassionally, just look at the videos from HPI Magazine.

For your info, DR, HR & MR Skylines are basically identical and mine has all the new hi tech bits, like coil over suspension, DR front & rear brakes, Cusco LSD, fully adjustable front & rear suspension and IF I choose to build this 3L stroker, I think it might be quicker than your GTS25t, now wouldn't that be embarrassing.

Link to comment
https://www.sau.com.au/forums/topic/49228-r30-purists/#findComment-985648
Share on other sites

i think b005t would smoke you  

you asked for an opinion, now dont cry if its not what you wanted to hear, or where you just after someone to justify a choice you have made?

l series engines are buckets of shit. but hey, do whatever you like.

That's an interesting thought.

On paper, I can produce at least 250rwkw @ 15psi from the L Series motor and my HR weighs just 1100kg. That would mean his R33 would have to have 300rwkw to just equal the same power to weight ratio, not to mention the enormous torque the 3.1 would produce.

You guys think the RB's are the be all and end all of engines, maybe I should just go for it and see how I compare on the dyno, you might be embarrassed as well.

It would be interesting if my "bucket of shit" out performs you eh!!!!!

I have built an RB30/25 DET and think I can equal or better the output with an L series of similar capacity. After all, absolute HP means stuff all if you can't get it to the ground successfully.

A mate has an L28ET running on straight LPG and point to point, he was faster with 145rwkw than he is now with 180, as now wheel spin out of corners is a problem.

Link to comment
https://www.sau.com.au/forums/topic/49228-r30-purists/#findComment-985845
Share on other sites

the old L series are built tough!!

i know of many that seem to go on forever if looked after.. i have 2 bluebirds with L20B's at home and one has done 350,000+ kms (speedo stopped) and thats my daily driver it still goes really well and doesn't hessitate to start.. my dad even said to me he was surprised it didn't blow any smoke! the other one blew a head gasket due to a broken waterline which ran through the inlet manifold. $30 head gasket and she'll be good!

and my L28 snaps the tacho round quicker than the RB does!

why not go twin turbo blow through mikuni's?? haha has anyone else seen that S14 in japan with the L31 setup like that?

Link to comment
https://www.sau.com.au/forums/topic/49228-r30-purists/#findComment-988110
Share on other sites

OHR30T, Yes the RB is finished, but thought I might shelve it for a while, as the 3L L Series sounds awesome, just think, No engineers report needed, no cat, just get a blue slip and go, as by chance, it will still be carrying the L20A engine number. Let our RTA & police have fun with that.

Haha,the "up yours RTA" value alone would make it worth doing! :D

And is it some people don't like old engines,or is it old Skylines? :)

Link to comment
https://www.sau.com.au/forums/topic/49228-r30-purists/#findComment-988855
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • That R31 was so cool. Only did Orange Park once. Scared the hell out of me.
    • Selling my TE37SLs since I've switched to smaller wheels.  They're for sale in Japan but it's pretty simple to send them overseas; USA excluded, since JPPost isn't sending there at the moment. Specs Front: 18x9.5j +22 5x114 Rear: 18x10j +20 5x114 Price: 320,000 JPY/ 3,285 AUD (current FX rate) Condition: a few scratches here and there, no bends, distortions or cracks.  Tires will not be included for international buyers, I'll get them dismounted before shipping. They're currently listed on yahoo auction and will be shipped in Japan with the tires if they sell here. Shipping costs to Aus: EMS (1-2 weeks): AUD 1,175 (current FX rate) Sea (2 months): AUD 460  (current FX rate)
    • The alloy coolant reservoir has a sight glass, so as long as I can see coolant in the sight glass it's GTG, as for PS, it isn't anything catastrophic if it gets low, and as it hasn't lost a drop since I have owned the car I cannot see it being an issue, even after putting the "big block" 2.5 in....LOL The only time it gets slightly messy is at oil changes, as the oil filter sits above the frame, and I need to use a plastic bottle with its bottom cut off to catch the flow when loosening the filter
    • Good on you for taking on the job, but it is a big one. Even if you have bolt on manifold and turbo, you will need: Post throttle pressure source to boost controller to wastegate (and FPR, and ECU/MAP sensor) Pre throttle pressure source to top of BOV(s) Oil feed - you can take that from the standard port in the middle of the block Oil return to block under the turbo - this is much trickier than it seems to route a decent/wide pipe past the manifold. You really can't use rubber hose because it is way too hot there, and also the oil out of the turbo core is a bit frothy so it needs to have a decent diameter Water feed - you can take that from the standard port in the rear of the block. Water return - mine runs to a T into the heater box return, just make sure you don't create a high point making bleeding hard. All of those lines should use 200 series style teflon braided hose with heat shielding because everything needs to be routed past the manifold. Also a turbo beanie is a really good idea to minimise the chance of the car catching fire (under bonnet lining in particular) You also need to decide a cam cover breathing solution as well, will you vent externally via a catch can (probably illegal) or return to the intake (plumbing required and can oil up everything over time) Keep in mind the intake and exhaust piping in the engine bay will be custom so you either need to be able to fab ally and steel or have someone you can get a car that isn't running to. Get the wideband fitting welded into the dump pipe at the same time. Also, just my opinion, a screamer pipe attracts attention and doesn't add power, I'd plumb it back if you want to be allowed to keep the car on the road. BTW do you know anything about how healthy the motor is, and what power you are targeting? Doubling or tripling the factory power on an unknown motor is a little risky. Also fuel system will need some attention (pumps, high current hanger, direct power and earth feed, injectors etc)
×
×
  • Create New...