Jump to content
SAU Community

Recommended Posts

Normally, when you travel over about 20 km/hr the door's automatically lock.

I found this annoying so decided to remove this function.

Firstly, remove the glovebox, theres about 4-6 screws holding it in and clips on the left hand side, be careful not to break them.

You will see a black box on the left hand side, this controls the central locking.

To make sure you have the right box, trigger the central locking and you will hear a clicking noise coming from the box.

Cut the green wire going into the box as shown in the picture.

All done!

Put the box and glovebox back together again.

Thanks to MadYeti on SDU for the information on which wire to cut.

Dave

  • 2 weeks later...
  • 3 weeks later...
  • 7 months later...

ok .. i have a prob

i cut the green wire, but the door still locks itself

errrmmm so what wire did i cut lol

havent noticed the car do anything strange yet, so i hope it wasnt a vital wire

lol

-Ruffels

  • 4 weeks later...

I DO have a viper alarm... you could be right.... At the moment the siren goes off it's banana unless you have the disable key in it.... washed the engine bay out this morning, must have some kind of short... hopefully it will clear eventually!

  • 3 weeks later...

definately doesn't lock here at any speed, and as far as I can tell, there are no wires cut anywhere, and I've been in the door well too, and nothing cut there.

I would like it to lock at 25km and lock when key removed if anyone knows how to get it to this without it being a function of an aftermarket alarm :(

  • 1 year later...
series 2 - locks about 5 seconds after the ignition turns on! i'm used to it... it unlocks when you turn the motor off, do the series 1 do that too?

I have a series 1 and it locks both doors after 20k's or so and when the ignition is turned off it only unlocks the drivers door.

I have a bit of shit i take to work with me and instead of dragging my bag out of the drivers door i go around to the passenger side and ge it, i have to arm and dis-arm the alarm every time coz i forget to unlock the passenger door before i get out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Grind them off, drill them out. Repair any rust on the other side. Start again from scratch.
    • Big R34 GTR parts cleanout. I have a lot of stuff collected over the last 14 years and my missus is giving me hard time. Make my life easy.   Nismo GT carbon fibre diffuser fins (discontinued)  NEW  $2900 Garage Defend Stingray canards carbon fibre  NEW  $1300  Top Secret G Force carbon fibre front diffuser  NEW  $2000  Haltech Elite 2500  NEW  $2500  Haltech Platinum Pro R34 GTR   USED  $1400  Apex’I power FC D'jetro + hand controller R34 GTR   USED  $1400  Nissan OEM BNR34 ECU  USED   $1000  HKS EVC 6  USED  $600  Blitz dual SBC ID boost controller.  USED  $350  TRE 255 LPH Fuel pump  NEW  $100  Fujitsubo  Super Ti exhaust  USED  $2700  Tomei Expreme Ti exhaust  USED  $2000  Trust stainless steel front pipe  USED  $1000  Apex’I super suction kit  USED $400  BC BR coilovers  USED  $600  Hardrace front upper camber kit. USED  $300  Garret 2860-5 turbos –  one good, one needs reco USED  $1000  Nissan OEM Toshiba MFD Screen replacement  NEW  $450  Nissan OEM BNR34 Series II front passenger seat  USED (mint) $5000   Nissan OEM BNR34 front bar in TV2  USED  $1000  Nissan OEM BNR34 front lower air spoiler  USED  $900  Nissan OEM BNR34 front lower air spoiler (painted)  USED  $900  Nismo front indicator (clear) USED  $80 Nissan OEM BNR34 radiator  USED $500  Nissan OEM BNR34 turbos  USED  $500  Nissan OEM BNR34 intercooler USED  $800  Nissan OEM BNR34 front swaybar   USED  $500  Nissan OEM BNR34 intake pipes   USED  $400    Also have a square set of uber rare Volk CE28n in 19*10 +22. Not really keen to sell these but make a high enough offer and maybe I will. If you don't know how much these usually sell for don't bother.   PM for pics.  Pickup Chadstone VIC or postage at buyer's expense.
    • Thanks Mate, I did know you could do that but i know there is a pump out there that you can bolt on and it all lines up. I was told about it and then forgot the model, I figure if i am pulling it apart i will just put a new one on 
    • You can also remove the veins from the HICAS portion of your existing pump. 
    • Trying to swap the rear subframe on my R34 and can't remove the L-shaped stay brackets between the front subframe mounts and the sill/chassis. I'm in the UK so rust is a problem. I've used loads of WD40 and then Tunap 103 for days beforehand. I backed off the bolts forward a bit, backward a bit repeatedly for ages to try and avoid snapping. They have all moved a few full turns. The one I've spent most time on has come loose and I can turn with fingers, and it will pull down and push up 2-3mm. But it won't come out. I can tighten it back up and loosen it off again repeatedly but it still won't come out. I assumed there's a captive nut inside but if that's broken loose then I can't understand why I can always tighten the bolt back up - I'd expect it to just spin both ways. Any ideas what's happening here? I can't visualise what's inside there to cause this.
×
×
  • Create New...