Jump to content
SAU Community

Recommended Posts

also, what time?

Hehe making times could be a mistake with this crew. Nah if it's only you me and andrew on friday night then it will be easy. I'd say just whenever we are ready. Try to make it around 7 to 8 at Andrews. Will take you an hour to get to his from the CBD. But I guess we better ask Andrew if it's ok to meet at his first thou.

  • Replies 89
  • Created
  • Last Reply

Top Posters In This Topic

Hey Al,

Yeah mate shouldn't be a problem at all. Your both welcome. We might get you to chip in a few bucks to keep my mates mum happy. Wont be expensive at all. Just tried to call you back, but went straight to msg bank.

What day / time you thinking of heading down?

Ok - I want a bed! :)

Duncan - you can meet at my house and we'll go from there - I will give you easy to follow instructions later.

Remember we have Geoff and Emre on Sat night too.

Shivram - your boss get in?

Thanks Snowie for looking out for us.

Chris, I'm coming down Sat afternoon sometime so just a single for me. Thanks a bunch mate. Chipping in is no problem. I know kinda where to go but I'm sure I wont miss it.

Yep Aaron is in with his STI and Frank will also be there (he has a worked 33 GTR, twin 2530's etc).

Should be a great weekend. I'm considering buying a video camera atm.

thanks for your help Andrew :)

Shivam.

Shivram - your boss get in?

I've never met Crazy Frank before - I know he knows Emre so this will be good.

Apparently my best time at PI is only 1sec or so behind Crazy Franks best - will be fun trying to match him for sure.

Also - the weather looks awesome for the weekend. I was actually hoping it was going to have a couple of short showers like last time. Was fun playing with Scotsman in the rain! :)

Ok Boys and Girls - just got a call from Chris Kelly to say that the HSV day is now full again. Apparently we have our own group for the track that will also include an M3, an M5 and a couple of Porsches.

He was also like "Damn you guys are fast apparently. Most of the guys are around the mid 2 minute mark with only a few at the low 2 mins." Basically no one under 2 mins. :D

Sounds like a come on. He must think we're stupid if he wants us to turn up acting like world beaters, only to get paddled.

I'd prefer to be amongst some of the other makes to see what they are running like and where they are fast.

and so we can burn a few of them. Light it up out of the corner and still pull past them on the straight.

I guess we will have to wait and see. Dont they do a super sprint at the end? Wont this mix up the field, because I think it's all based on your times throughout the day.

I'll be happy to crack 2:00 on street rubber.

 

The super sprint wil be awesome if it's what I think it is.

Go the road rubber. Its actually more fun on road rubber because your car moves around and it teaches you to be a lot more delicate with the controls.

But as far as lap times go, around place like Phillip Island, i think there is even more then usual to be gained from grippy tyres. A sub 2:00 lap time would be awesome, going on the GTST/GTT from the last day, that would be about a 1:55 on sticky stuff :D

LOL. my car still aint ready so good thing i didnt make plans for this weekend. Sandown is looking the good though.

Enjoy ppl and dont forget we need plenty of photos

Do NSW proud:) , the boys down here are starting to mock Team Trackday based on my lacklustre performances to date :Oops:

haha, just blame the car :rofl:

I dunno how I'll go, but at least I promise to "Drive it like I hired it" :bahaha:

Ok, Anyone who is planning on having a meal at the house. There was no BBQ there, so I'm bringing one down that we can all use. So feel free to bring you BBQ stuff.

Andrew - what time do you want to see me and Duncan tonight?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...