Jump to content
SAU Community

Recommended Posts

  • Replies 55
  • Created
  • Last Reply

Top Posters In This Topic

Geez - Imagine how pissed and r00ted I could have been if I had done that Chris -

frigging modified cars - it never ends -

never

never

never

even if you want it to

Your turbo will blow up

and you get a bigger turbo than before

so you want more response

so you upgade your RB25 to an RB30

And then you need brakes

And then you need suspension

and then something breaks

so you upgrade the broken bit

you get more power

and your gearbox breaks

so you fix that

and then something else breaks

and so on

and so on

and so on

:)

Geez - Imagine how pissed and r00ted I could have been if I had done that Chris -  

 

frigging modified cars - it never ends -  

 

never

 

never  

 

never

 

even if you want it to

 

Your turbo will blow up

 

and you get a bigger turbo than before

 

so you want more response

 

so you upgade your RB25 to an RB30  

 

And then you need brakes

 

And then you need suspension  

 

and then something breaks

 

so you upgrade the broken bit

 

you get more power

 

and your gearbox breaks

 

so you fix that  

 

and then something else breaks

 

and so on  

 

and so on  

 

and so on

 

:)

Breathe B-Man, someone pass the paper bag. :) So it was your turbo was it? Buy an R32 mate, throw away everything :)

LOL, my secret is to remember everything you do to your car will have to be a compromise, otherwise you are right you could easily spend countless thousands on trying to make it as all round a performance car as something like a GT3.

We are Ozzies, think Phase III, dont worry about brakes or susp, sink pi55 whilst your sux nitrous Max :)

Also, at the moment i have my bov (hks ssqv) in the stock postion. When i install the fmic, is it best to put the bov on the pipe coming out of the plenum?

HI~~13_devil....can u pm me?may i know how u install the SQV in the stock position?i cant find any bracket for SQV install to RB25det stock position....thankx...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Need to see other side of PCB in that area...ie; I don't see any thru-hole mounting, just soldered vias (smd zeners in SOT23 have 3 legs but only 2 are used, as reflected by PCB tracks)
    • 4 to 5 is fine. It will be slow, but that's better than blowing turbos. I don't have a PS pump idle up solenoid on my car, because... I think when we put the Neo in we retained my R32 lines. But.... From inspecton of the R34 vacuum hose diagram, you can see that the solenoid needs to be connected to the turbo inlet as source of clean air) and the plenum (as source of vacuum - which is the place for the air to flow to to cause the idle to increase). So 3 to 1 is VERY WRONG. 3 should go to either the turbo inlet, or the plenum. Follow the other hose from the PS solenoid and if it goes to the plenum, then your 3 goes to 2 2 would also serve as a bleed port for a boost solenoid.
    • Pull them out and pull more apart. You can't do shit with them still bolted to the floor of the car.
    • Yes it is. ZD1 is on the other side of the board. Where ZD1 is marked is clearly opposite a 2 pin device. Our 3 pin device here is not a ZD.
    • Alright, a little update on this... I called Fulcrum, who used to be the distributor in Australia. No Bueno, they don't service them anymore.  Called shock works, who don't service them but offered to dyno the shocks for performance, and suggested DNA in Sydney might service them.  Called DNA, who also do not service them and basically said they try to steer customers away from tein for this exact reason these days- there is just no support for them anymore apparently.  Both SW and DNA said they are a not necessarily a bad product, but they just don't service the brand or know anyone who does service the brand anymore.  So... I could keep calling around but at this point I think I'll probably just spring for the shockworks product, unless anyone here knows anything.  Cheers 🍻 
×
×
  • Create New...