Jump to content
SAU Community

Recommended Posts

Hi Guys i got a problem with my car reving past 4-5 rpms... it starts to splatter... sounds like the pistons is goin to blow out of the block...

R33

RB25 DET

slight mods

- airfilter

- 3 inch all the way

- 9 - 10 psi.

only started not too long after i installed a FMIC.

also my fuel lid isn't pressurized. the seal is cracked would this do anything?

also just had a full 80K service.. all new iridium sparks still not sure why its doin this...

Link to comment
https://www.sau.com.au/forums/topic/52257-high-rpm-problem/
Share on other sites

- Even one cracked coil can cause a lot of hesitation!

- i was getting it between 4500 - 5500 rpm, and after that it was all good, it would rev out nicely...

- When i taped mine the problem went away, but after a week or two, came back b/c the tape shrunk on the coils, exposing parts of the crack once again

- I would be doing this to ALL of the coils, regardless of wheather there is a crack there or not, as it could crack soon anyhow as the others have....

umm... this sounds like wats happening exactly..... (4500 - 5500 rpm) but just a question wat is hesitation? its not like back fire is it? not poping from exhaust right?

Link to comment
https://www.sau.com.au/forums/topic/52257-high-rpm-problem/#findComment-1032433
Share on other sites

Yeah, that's what I was implying with that post. It pops, and misfires at around that point at WOT.

Even if you fix your coils, at higher boost, best case scenario is that instead of popping and misfire, you will get a flat spot at around that point.

You will need a new ECU, or a SAFC to retune your air to fuel ratios, as they get VERY rich at around that point with higher boost. I think that timing gets retarded too b/c of the overfuelling, hence the massive flat spot / misfire.

Even with a SAFC, b/c it runs leaner after a tune, the timing does not suffer as much. I only have a SAFC, and I have NO flatspot. In fact, where the flat spot used to be, there is actually a tiny surge or power.

Below is a pic of my dyno graph before and after the SAFC. (Note on the first run - green, my tuner backed off b/c the A/F ratios went crazy. Then sensor he was using to measure the A/F ratios was buggered and he replaced it after a couple of runs.)

Link to comment
https://www.sau.com.au/forums/topic/52257-high-rpm-problem/#findComment-1032816
Share on other sites

Hey Zahos

I am running 12psi and have an SAFC2. It been running great for months. Then on the weekend the car developed the same misfire you guys are talking about. popopop at around 5000rpm and a short drop in power. When I dropped the boost to 10 psi, the problem went away. The spark plugs should be fine as they are new. Would this be a sign the coil packs are on there way out?

Link to comment
https://www.sau.com.au/forums/topic/52257-high-rpm-problem/#findComment-1041688
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...