Jump to content
SAU Community

Recommended Posts

I spotted a red i think was series 1 with red number plates that somehow spelt stagea. in milperra on the m5 bridge

haha i have the same car.. but in perth.

red S1 with STAGEA plates.

when i tried to get a REVS check on my car in WA the lady kept saying it was under finance, but it wasnt. it was the damn one over there but she didnt tell me that!

Shaun

Spotted a light green series 1 with gold moulds on Rooks rd Nunawading sitting outside Kamikaze motors,Cood have sworn i saw that car 4 sale in that same showroom two weeks earlier, hmmm duno bout the gold moulds :laugh:

Spotted a Yellow Series two on the Pacific Hwy near the Great Northern Hotel.

I was going the other way and waved, but i dont think they saw me.

Its the first Stagea I have seen on the road since getting mine.

Ben.

That could well be Andrew "wolverine" or his wife. Did you get a chance to see if it was an RS Four S?

I spotted a nice black beauty on the road between childers and Bundy! I think it was a series 2, bit hard to say, it was all but past me before i noticed!

MAn I'm slow sometimes!

That was on Sunday the 25 feb.

spotted a series 1 with chrome rims this morning turning onto armidale road had a forsale sign on it and he waved back when i waved.

also have seen radiums car every morning last week on mounts bay road.

also spotted a white series 2 stagea with r34 gtt rims at bp in thompsons lake tonight about 7pm was nobody in it

Spotted a silver s1 Stagea heading into the complex where Unique Autosports used to be in Castle Hill, around 5.30pm tonight... Looked to have standard wheels, so it wasn't "PranK" Christian's old car - his has s2 taillights on it anyway...

i saw a wicked Silver S1 on smith street down the gold coast.. came out of an on ramp 2 cars in front of me i was on the fone hung up and chased him got side by side giving him the thumbs up then pulled slightly ahead to check out the front of it. it had a nice front mount on it with a full Dayz kit all the way around {mine has a dayz kit minus the front bar extender} it was an auto aswell cause he upped it and i could hear it kick back and it sorta did the exact sae thing mine did...

lol now thats a long post.. must be the boredom and insomnia kicking in :O

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...