Jump to content
SAU Community

Recommended Posts

Vic spotted, stock m35 grey arx on Wellington rd, rowville about 3pm.

...... Badged as M35? Wierd......

Hi Troy, that was me. Why is it weird? I have been looking to buy the Stagea and ARX badges to put back on the car, but cant find them. The M35 badge is actually from an Infiniti M35. Replaced it when the tailgate was re-painted a few months ago. Car actually came with M35 badge when I got it. I think it keeps people guessing even longer.

My V36 Coupe has all Infiniti Badges including the drivers airbag.

Hi Troy, that was me. Why is it weird? I have been looking to buy the Stagea and ARX badges to put back on the car, but cant find them. The M35 badge is actually from an Infiniti M35. Replaced it when the tailgate was re-painted a few months ago. Car actually came with M35 badge when I got it. I think it keeps people guessing even longer.

My V36 Coupe has all Infiniti Badges including the drivers airbag.

Nice to see your ride mate, I was next to you in the grey pajero trying to see an infinity badge on the grill ; ) flashed my lights also.... Then remembered I wasn't in the stag.... : (

Wierd cause I hadn't seen that badge before.

Blue M35, parked Wolsley Place, Thomastown today. Had a busted front fender.

digging up an old post.. but i think that was me. out seeing a customer..

But the only time i get seen is when i had the ding. All fixed up now.

on another note.

saw a black stock (looked stock) M35, you gave my car a good look over.

I gave you a nod and a lil wave but not sure if you saw it.

Driving city bound on the eastern fwy, 740ish tuesday morning.

i get a little excited when i actually see Stags getting around.

I feel like the only one getting around at times.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...