Jump to content
SAU Community

Recommended Posts

hi how are you

got a 1991 r 32 gtst front cut i have taken motor and gear box only

all pannels most interior parts

front bumper has electric motors in it to adjust front end

also got a/c pump and power steering pump

and projector headlights and side indercaters

suspenchion arms and hubs too

if any one need ne thing ask me

also a 1994 r32 gtr front cut left over parts most parts minus engine and pannels avalible such as front drive shafts cross member pedal box abs unit power boster and matser cylinders both clutch and brakes front sway bar lots more just ask

have compleate set of h/adjustable bilstien suspencion 4 r32 gtr 550 including freight ne were in aus all wishbones avalible and perf con front stering rack

also apexi pod adaptors 4 std gtr afm`s

r32 gtst parts

front bumper $200 with electric motors

steering colum calapsable type with ignition $100

std air box $30

a/c pump $150 with a/c rad and fan

power steering pump $80

speedo cluster $130

if ne thing else needed just ask

  • Replies 85
  • Created
  • Last Reply

Top Posters In This Topic

also a 1994 r32 gtr front cut left over parts most parts minus engine and pannels avalible suck as front drive shafts cross member pedal box abs unit power boster and matser cylinders both clutch and brakes front sway bar lots more just ask

bonnet per con no dents black in colour $200 ono

left hand side pannel per cont black in colour $100

front bumper $200 with electric motors

steering colum calapsable type with ignition $100

std air box $30

a/c pump $150 with a/c rad and fan

power steering pump $80

speedo cluster $130

also compleat set of bilstien hight adjustable sus 550 compleat set

if ne thing else is needed just ask

cheers

The front bumper for the r32 gtr is that the front bar from the head lights down?? If so how much for freight to Melbourne?

:burnout:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...