Jump to content
SAU Community

Recommended Posts

Well they do say the best gift to give is one you would like to receive yourself. :D

You will need the plumber buddy.^

It aint hard Shell - just take up to an hour to do the lot.

$20 bucks max if you DIY.

Richard, I never knew you cared. What does a plumber charge to change an Oh Ring? LOL

Shell, yep it's not difficult as long as you can turn off the water, have a good sized shifter and the correct washers but mixer taps can be tricky.

Richard, I never knew you cared. What does a plumber charge to change an Oh Ring? LOL

Shell, yep it's not difficult as long as you can turn off the water, have a good sized shifter and the correct washers but mixer taps can be tricky.

haha snap... yep the water is the issue. No mixer taps.

Yeah, apartments may not have an easily accessible water switcherofferer. Might be central not individual.

If you rent, I'd be at least be contacting the Landlord if in doubt.

Look for a small panel or door in one of the walls,

Its probly in the laundry, or hidden in a cupboard or wardrobe,

There will be a tap, you may have to look around with a torch inside the wall to find it.

Or if it has an underground carpark they may be on the ceiling down there.

I have most plumbing tools, includung the tap reseater you will want for this job.

Ps spend the extra 5c per washer and get the good ones

Edited by D.I.Y. Mik

And...

Leave the taps open when you turn the water on to flush out the brass shavings,

closing the tap on shavings just puts a groove in the washer and they leak.

Hydroseal is a good lube for them, and you may need to seal the thread again with teflon tape or Lockseal.

Leaking spindles need replacing, they are cheap and its easier than refitting o-rings etc.

dads rule!

Edited by D.I.Y. Mik

thats sick! i have a lazy mans 4 foot with just your average tropical fish lol. my dad has an 8 foot in wall salt talk with clown fish and shiz. but im way too lazy to put that much effort in

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Power steering is probably because someone has nuked the HICAS CU and you no longer have the variable power asist doing what it is supposed to. How much boost are you running? You are aware that any more than 10 psi on the stock ECU is just asking for it to go to full R&R (that's Rich & Retard, which is effectively Retarded and Retarded!) which kills all the power. Depending on the exact conditions, it can just be runnign on the fat and stupid end of the maps, then the conditions change, you make a little more boost and the ECU goes into panic.
    • @BuiltNotBought Just as GTSboy said.   If you want driveabilty and more low down torque..keep the stock runners. They are VERY good from a factory. I have them too on my RB25DET NEO and as a GTSboy i have fmic but with stock piping route(i have Blitz intercooler) Iam making around 320 BHP and the car pulls "hard" from like 2,5k all the way to 7k. I have it dyno tuned to mimic N/A power curve and making little less max torque due to the smallbox tranny. But driveability is very great. I had 350Nm below 3k so car feels very quick.   EDIT:  Not my channel but i saw this and i know that is what i want (and i have exactly this)  
    • Looking to sort out a couple of issues on my skyline  It recently was rebuilt, however rebuilder long story short did not give two flying effs about the work he did. So moving forward it's running but I have two persistent issues 1) it has a misfire / lag type of issue (was at higher RPMs but I had a dead piggy back ecu removed which improved it) now it's not as bad but still does it at random, I thought it may have been a boost issue I'm running an older turbosmart dual stage controller, turbosmart told me to try running off gate pressure however it still has a lag at random times. It has New MAF, maf plug, coil packs, sparks, CP harness.. injectors tested and cleaned. Factory ECU. 2) Power steering issue. It is tight as anything. Flushed power steering, rebuilt my pump because the bearing was shot. Flushed again still tight (mainly when parking and going slow into my driveway etc)  No kinks in hard lines, replaced the lines I could see had cracks. Still tough to steer.  I was told to shim a coin and place into the solenoid plug? Is there anything else. My steering angle sensor also has a issue. It's a used one I replaced, does it need to be calibrated? I feel like I've tried everything and this car is my voodoo doll.   
    • Holy shit... wow!!! I totally missed this
    • One main filter. Each tank has a prefilter to keep rocks and small children out, then the big main filter that also does water separation. Clogged the first one so bad it was like a rev limiter at 3200rpm. Literally just like dropping the throttle off and maintaining rpm!
×
×
  • Create New...