Jump to content
SAU Community

Recommended Posts

Do they have grooves carved into them?

Is there a lip on the very outside edge?

Do they shudder or shake when you are on the brakes at any particular speed?

ie. at high speed / heavy braking or slow speed / light braking.

Hmmm, will have to confirm the list. However, I've been doing extreme light braking due to like the metal grinding sound. The car does shudder under high speed braking but, I never do that because I know my rear brakes are on their way out. Will have to check the grooves and the lip.

Also, how much is it to get new pads + machined vs new pads? Just trying to get a ballpark figure (Not a quote haha).

edit: by grooves do you mean like.. cut brakes? (like aftermarket?)

And by the lip do you mean the rusty old looking housing thing that goes around the brake?( Dammit, wish I knew more about cars so I could just give the proper name of parts) If so, that's sitting further out than the disk. The front however, are completely different where the disk is HEAPS in front of that rusty housing looking thing.

Edited by RosieR34

Metal grinding sound could be your pads worn out. Didn't you get them done?

Shudder at high speed is likely warped discs / rotors.

Grooves you should be able to see but use your fingernail and run it across the face of the disc, if you feel deepish grooves in the face...

Lip will be felt at the very outside of the disc face with fingernail.

If there is a lip on the discs just get new discs man. I just had my fronts done with pmu discs and pads and it wasn't overly expensive. And you can get it heaps cheaper. If you like Jeremy take a pic of your discs and upload them. Or geOra north sider to have a look for you.

If it's the rear it's more likely you just need new pads and the rotors are fine.

Pics and we can tell more.

Xoxo gossip girl

Thanks peeps.

From the quick look I had earlier the discs were clean (No grooves and no lip). HOWEVER, I will need to 100% confirm. Those two things I would've noticed and questioned if my discs were damaged. I am hoping for my discs not needing to be machined because that is coin I do not have to repair them. I was told brake pads were like $50? that's a price I am willing to pay for haha

More like $120 for cheap standard pads.

$200-$300 for good ones.

Good thing is, its VERY easy to DIY. Wheels off, pop the spring out, swap pads, and put it all back.

I found a little bit of metal riveted to one of my rear pads. It was bent around to act as an alarm. When the pad got worn down, the metal started to make a horrible scraping sound on the disc.

yeah that's probably what it is Mik :yes:

YeaH Jeremy it will be a few hundred, 100% worth spending the extra and getting good pads. you don't

http://www.nengun.com/top-secret/super-street-brake-pads

That's pretty good value

I only need rear pads. The fronts are about.. 12 months or so old and tbh, I am an extremely like breaker, I like to roll to my stops as much as possible (of course avoiding traffic harassment :P).

Thanks peeps :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • 98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • When you say your cams are 272/262 is that 272in and 262ex?
    • We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...