Jump to content
SAU Community

FAQ: BA Falcon and stereo changes

paulr33

By paulr33,
in Car Audio & Electrical

 Share

Recommended Posts

paulr33 Grand Master

paulr33

Posted
Posted

Q) I have BA Falcon and I don't like the stereo

A) Read below

My friend got his xr6turbo mark II yesterday and we went to garys car radio to check out stereo options for it.

Headunit and Engine Management System

The BA falcon head unit is part of the engine management system and if removed/disabled it will cease to function and render the car un-startable. The headunit system is about $2000 brand new if its busted or damaged. They can also be repaired for a small fee to a few select electronic freaks if the damage isn't too bad. There have been some cases of the unit being damaged by tampering and you have one of those two options, costly either way.

Premium Sound vs Standard

The head unit I am talking about is the sound upgrade option. Not to be

confused with the Premium Sound option which has the TV display. The upgrade sound option has a 6 disc built in stack and its the stereo control and aircon control in one.

3rd Party Headunits

If you want to install your own head unit it must be installed in another location, the first place would be where the cigarette and tissue compartment is. We had a look at a BA falcon today that had this setup. The only downside to this is the factory head unit is still there and still works, just no sound comes out of it. You can then tap your head unit into power, acc, ground and speaker wires according and the other downside is the head unit is down low and just in front of the gearstick

New speakers & Amps

If you opt to keep the factory unit which you can do then you can get the front speaker wires, install a stinger high gain adapter and use it as a form of RCA out. The stock headunit doesn't have RCA preamped/gain outputs so you have to use inline adapters. You can then run these to your own amps and replace the factory speakers with 6" splits and and subs and amp to your hearts content. We got an install that used the front wires with an inline adapter and this ran the fronts and rears on a 4 channel amp. The rear speaker wires from the stock head unit were plugged to a monoblock amp and the set off to run 2 x 10" subs.

Caution

We were cautioned about doing this setup in the event of spark or voltage surge the factory head unit could be damaged or placed at risk and then be up for some costly repairs. The solution was to use inline fuses on the speaker wire so they break before the voltage/surge gets to the head unit. Although not 100% a lot better.

Result

This was the most cost effective and easiest method whilst retaining the factory system as it has controls on the steering wheel to choose tracks etc.

The standard system is a 6 disc in dash changer so its not too bad as a full package.

Conclusion

It seems Ford wanted to prevent people from changing the head unit and tampering with its sound setup. If you want better sound and a better setup they wanted you to get the premium sound option.

:)

Link to comment
https://www.sau.com.au/forums/topic/55334-faq-ba-falcon-and-stereo-changes/
Share on other sites
sewid Grand Master

sewid

Posted
Posted

fun stuff!

As an aside Nissan tried to do some similar stuff with the R34 GTR and the built in LCD display has no RCA input or any easy way to plug your own video source into it unless you option it when you buy the car. They had at least 10 different Navi/TV options you could choose from the factory and/or dealer.

Luckily nowdays there is a guide floating around on how to hook any NTSC video source up with a bit of soldering and I have done it on mine, installed a DVD headunit, and watched "The Usual Suspects" on the screen the other night. Works brilliant :P:)

Chris Rogers Grand Master

Chris Rogers

Posted
Posted

fun car to work on. (BA) did one today with TV interface and a decent stereo as well.

this one had the premium system on it and I still have a bit of a probelm with engine noise on it . this is using the stinger line out units.

if you are playing with the unit ( IE pulling it out) have the keys handy.

still waiting for someone to throw a 34 GTR at me...

Chris Rogers Grand Master

Chris Rogers

Posted
Posted

still waiting for an alternative mounting from aeropro. was talking to the local rep and he's says if theres enough interest then they will make one...

( I already get 5-6 called a week on VY commys.. same problem easier solution.)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      "Cheap" bolt on turbo on RB25DET NEO

      By Kapr · Posted

      You are selling this? I have never bought something from marketplace...i dont know if i trust that enough. And the price is little bit "too" good...
    • Watermouse
      "Cheap" bolt on turbo on RB25DET NEO

      By Watermouse · Posted

      https://www.facebook.com/share/19kSVAc4tc/?mibextid=wwXIfr
    • Kinkstaah
      Airbox for +T

      By Kinkstaah · Posted

      It would be well worth deciding where you want to go and what you care about. Reliability of everything in a 34 drops MASSIVELY above the 300kw mark. Keeping everything going great at beyond that value will cost ten times the $. Clutches become shit, gearboxes (and engines/bottom ends) become consumable, traction becomes crap. The good news is looking legalish/actually being legal is slighly under the 300kw mark. I would make the assumption you want to ditch the stock plenum too and want to go a front facing unit of some description due to the cross flow. Do the bends on a return flow hurt? Not really. A couple of bends do make a difference but not nearly as much in a forced induction situation. Add 1psi of boost to overcome it. Nobody has ever gone and done a track session monitoring IAT then done a different session on a different intercooler and monitored IAT to see the difference here. All of the benefits here are likely in the "My engine is a forged consumable that I drive once a year because it needs a rebuild every year which takes 9 months of the year to complete" territory. It would be well worth deciding where you want to go and what you care about with this car.
    • GTSBoy
      Airbox for +T

      By GTSBoy · Posted

      By "reverse flow", do you mean "return flow"? Being the IC having a return pipe back behind the bumper reo, or similar? If so... I am currently making ~250 rwkW on a Neo at ~17-18 psi. With a return flow. There's nothing to indicate that it is costing me a lot of power at this level, and I would be surprised if I could not push it harder. True, I have not measured pressure drop across it or IAT changes, but the car does not seem upset about it in any way. I won't be bothering to look into it unless it starts giving trouble or doesn't respond to boost increases when I next put it on the dyno. FWIW, it was tuned with the boost controller off, so achieving ~15-16 psi on the wastegate spring alone, and it is noticeably quicker with the boost controller on and yielding a couple of extra pounds. Hence why I think it is doing OK. So, no, I would not arbitrarily say that return flows are restrictive. Yes, they are certainly restrictive if you're aiming for higher power levels. But I also think that the happy place for a street car is <300 rwkW anyway, so I'm not going to be aiming for power levels that would require me to change the inlet pipework. My car looks very stock, even though everything is different. The turbo and inlet pipes all look stock and run in the stock locations, The airbox looks stock (apart from the inlet being opened up). The turbo looks stock, because it's in the stock location, is the stock housings and can't really be seen anyway. It makes enough power to be good to drive, but won't raise eyebrows if I ever f**k up enough for the cops to lift the bonnet.
    • BuiltNotBought
      Airbox for +T

      By BuiltNotBought · Posted

      There is a guy who said he can weld me piping without having to cut chassis, maybe I do that ? Or do I just go reverse flow but isn’t reverse flow very limited once again? 
×
×
  • Create New...