Jump to content
SAU Community

Recommended Posts

  • Replies 70
  • Created
  • Last Reply

Top Posters In This Topic

Going by some quick research, so long as you have quad pintle injectors like HKS/Nismo/Apexi then you should have zero problems with idle and fuel economy. It seems the RX7 and SARD injectors are the non-DOHC friendly types and thus you get what you pay for. It seems people with SR20s have had no problems with 740cc quad pintles!

joel mate rx7 ones are fine the spray is pretty much a stream as you say but this is due to the pinttle cap hole being to narrow you need to use toyota ones and drill them out slightly but the patter is quite narrow as opposed to your nismo quad pinttle varieties, but 550cc is small so the differences will be quite small....Also some of the earlier rx7 injectors will actually require you to bore the hole in your head slightly larger so be carefull what you buy if you go down that route. Personally i could never pay the ridiculous prices asked for by the jap brand injectors its bloody daylight robbery.. i use holley injectors in my car (110lbs= 1180cc Units), cause they are cheap, never fail, and alot of the product range is designed for methonol so the seals are alot higher grade but you will not get you your misty spray with these they are pretty savage but very effective!!!!

the rochesters are the same as the holly design they have holes that seperate the spray to give a finer spray pattern but are still single needle or pintle design i will post a pic of the design!!!

Hi Joel, I have a set of 555cc nismo injectors in my RB20. I actually had them checked for flow before i installed them and the results showed that they all flowed Exactly the same amount - 600cc. So yeah, im happy with them but i can't comment on fuel economy as i had a bigger turbo and stuff put on at the same time :D

Generally bigger turbo's under normal driving conditions result in better fuel economy as you tend to be on boost less.

Note the normal driving conditions. :D

Has the fuel consumption changed dramatically even with the mods or?!?

Generally bigger turbo's under normal driving conditions result in better fuel economy as you tend to be on boost less.  

 

Note the normal driving conditions. :)

 

Has the fuel consumption changed dramatically even with the mods or?!?

Fuel consumption has got a lot better now that i'm running the stock ecu chipped, especially for highway cruising compared with the microtech that i previously had.

I am lucky to get 300km/h to a tank now with 550cc injectors and GT30 turbo, and thats driving to work and back everyday when my car rarely sees over 80km/h or 4000rpm

One shot at "300km/h" per tank... nice effort mate :P

LOL above

Hey I have YELLOW 555s

Can the colour give an indication on what injectors i may have cause i have no idea

Cheers :D

Well they won't be nismo ones because they are pink, so i dunno....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah pretty impressive hey, good to see quality products not over-shooting their prices. That's what drew me to buy the hypergear turbo, just a shame I've never got the chance to see it in action
    • Thank you GTSBoy and MBS206 I have done the compression test with the motor out of the vehicle, reason for the test was to see if I needed to remove the head and do rings etc while its out. I'm in the process of respraying the vehicle and tidying up a few things. Story behind it all is I've just purchased the skyline and it was running when I got it, never drove it on the street though as I wanted to pull it down and do it all up again before registering it. the gentleman I purchased it from told me the motor has a forged bottom end and has a decent tune through it but I was going to pull the sump off anyway to see if it is a forged bottom end. that's why I thought id do a compression test beforehand. 
    • Man, I'm kind of amazed that the price of the turbo has not changed in 7 years. Everything else is inflating beyond reason, but not this? Good on Tao / hypergear I guess? Anyways, good luck with the sale!
    • I'm selling my brand new, in the box, never used Hypergear ATR45 - and I had some additions I paid for a few yrs back when I purchased it. Never ended up having the rest of the money to add all the mods at once, so I just ended up slowly selling each part. I originally had it internally gated, with the dump pipe, however I found it was incompatible with what I was going to use it for, so I contacted (I think Ken) from Hypergear, and he and I messaged back and forth & he got me to ship the turbo back, where they modified it & made it externally gated, and gave me the 5 bolt dump pipe attachment for custom welding. (Photos below) This turbo like I said has never touched the inside of an engine bay, it's completely brand new, never used, been sitting in the same box it arrived in, covered in plastic & all. Below are the photos of it: And while the guys at Hypergear were making it in-shop, they sent me some photos of the process: I'm looking at selling this just because I'm in need of the money right now, and don't have plans on modifying the 34 anytime soon - and from reviews & peformance sheets, this turbo had amazing results back when I was researching. The turbo was purchased in 2018 for $1.9k, with the mods I got added on. Looking at the website now, for the same turbo they sell (ATR45SAT), with the current addons it adds up to $1830 for the turbo Current addons included: - Bolted dump adaptor - Ball bearing CHRA - Braided oil feeding line So I'm looking to possibly sell it for around $1800, with shipping included in that 1.8k, It cost me around $120 to ship - so yeah thought I'd throw it out there and see if anyone was interested in purchasing. Cheers!
×
×
  • Create New...