Jump to content
SAU Community

Recommended Posts

Sometimes when you watch the odometer tick over, it looks like it's jammed then quickly flicks over.

Bushes are the best indication cause dodgy people don't change them, mainly the obvious like gearknobs, steering wheels and pedals with aftermarket stuff.

Link to comment
https://www.sau.com.au/forums/topic/5663-wound-back-od-meter/#findComment-85599
Share on other sites

Well if it stops on the next thousand/10 thousand.. It usually means its been played with :P

We've had this happen to ours. One time it just stopped and didn't move for 400k's. So we took it to the mechanic and he fixed it and said it has been wound back a fair way. Every now and then it stops.. then it starts again :P

Link to comment
https://www.sau.com.au/forums/topic/5663-wound-back-od-meter/#findComment-85774
Share on other sites

Clock winding is way too common. The drivers seat is a good indication as mentioned. Also the steering wheel and the gear knob, as they wear the most.

Ive seen TOO MANY imports with completely worn steering wheels and gear knobs, very worn trim etc, only to see 50 or 60 grand on the odo- and the dealers seriously expect us to believe they are genuine k's! Maybe they believe it themselves.. A car with 50,000 genuine ks should be practically new. This is considering many imports with 90,000 ks can still clean up pretty damn well.

Its a worry. Or you get a car in seemingly near new condition, that has a noisy timing belt indicating 100,000!!

Bottom line is too many dodgy operators. Apparently it happens in Japan, and not by people here when they land.

Link to comment
https://www.sau.com.au/forums/topic/5663-wound-back-od-meter/#findComment-85801
Share on other sites

Originally posted by zerorespect

it's always buggered me why every1 (nissan, honda, toyota, etc)hasn't gone to digital odometers - maybe controlled by a box marked with the chassis/vin number of the car to hamper swap overs...

Its so they can send them over here and make some $$ :)

Link to comment
https://www.sau.com.au/forums/topic/5663-wound-back-od-meter/#findComment-86208
Share on other sites

Mine's 93 with only 32,000km on the clock when I bought it... some of the numbers are not aligned which maybe coz it's been wound back prob in Japan or somewhere here. But all the interior trim, steering wheel, etc etc are in immaculate condition, so could it be that cars with original km still have numbers on the odo misaligned as well? The odo is runnin smoothly none of the above probs happen so far. I haven't check the suspension bushes thou, not sure how to look at them.

But I travelled a lot... 7 months ownership & now I've travelled 9000km in it....

Link to comment
https://www.sau.com.au/forums/topic/5663-wound-back-od-meter/#findComment-86677
Share on other sites

Originally posted by rs73

Mine's 93 with only 32,000km on the clock when I bought it... some of the numbers are not aligned which maybe coz it's been wound back prob in Japan or somewhere here. But all the interior trim, steering wheel, etc etc are in immaculate condition, so could it be that cars with original km still have numbers on the odo misaligned as well? The odo is runnin smoothly none of the above probs happen so far. I haven't check the suspension bushes thou, not sure how to look at them.

But I travelled a lot... 7 months ownership & now I've travelled 9000km in it....

Mine was basically the same.. had 33000km on the clock and

everything was still sweet.. but definately the clocks been

played with cause I've had to change my clutch after 11000km..

But these engines are so robust... I've done 30,000 in 10 months

and this thing is a weekend driver...

Link to comment
https://www.sau.com.au/forums/topic/5663-wound-back-od-meter/#findComment-86836
Share on other sites

It happens to so most imports i'd say... mate bought a 96 GTS25t skyline in immaculate condition.. showed 11,000km on the clock, seemed close to it aswell. His clutch died completely within a week of driving the car normally. We later saw the exact car on prestigemotorsport website after it was imported (with perth plates on it, rego sticker), saying 52000km. It was owned and driven around in perth for a while then sold to a dealer who my friend bought it off, so it would have been wound back here. No way a clutch on a totally dead stock r33 is going to fry itself to nothing within 11,000km of its life, unless it has been thrashed mighty hard since new, but since the car was stock you would doubt it.

Link to comment
https://www.sau.com.au/forums/topic/5663-wound-back-od-meter/#findComment-86862
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...