Jump to content
SAU Community

Recommended Posts

yo, im realy intrested in 1 ov your cai boxes and im sure alot ov the 33 crew on tha coast will be too! i was going to make 1 myself but i dont mind spending the money and getting 1 made. i have the stock intercooler but i cant understand where the pod will get the cold air from.

Im realy keen on 1 ov your cia boxes if u fill me in where the air is coming from. will have to be next week as i just spent 600 on a hks sequential. keep me posted.

Gamma :(

  • Replies 141
  • Created
  • Last Reply

Top Posters In This Topic

yeah around 600 with adaptor, ssqv, gettin fitted tuesday. i dont hav the snorkel where can i find 1, ive posted an add in tha wanted forum. Do they come with a snorkel (probs stupid question). if i can get tha snorkel well do buisness 4sure!!!

keep up tha good work.

they dont come with a snorkel but ur bound to find one on the forum sooner or later. maybe even ebay?

I didnt really notice a difference in performance - guess I got one cos most people were sayin that Iwas better off with a cai box over the top of the mushroom! (but Ive also read that a good panel fiter can be better!!) :confused:

Ah well - they look good!!

yeah around 600 with adaptor, ssqv, gettin fitted tuesday. i dont hav the snorkel where can i find 1, ive posted an add in tha wanted forum. Do they come with a snorkel (probs stupid question). if i can get tha snorkel well do buisness 4sure!!!  

keep up tha good work.

they don't come with the snorkel, but i got 1 at home.

u can have it for $15 :)

thanks Paul for answer a lot of the question too, hope every customer are as good as u :(

  • 3 weeks later...

Hi maxx,

Any available for r33 gtst? i am in melbourne. Let me know cost including shipping

Also what pod filter is suited for this box? Can you supply that as well or exact model?

can u custom make them to be feed tru the snorke AND a duct hose on the front of the box, [as in from the front bar to the front or bottom of the box..lets say 4inch hole to fit a ductin hose? for r33 s2 by the way

paulR33: i still got 1 left i think, but already order some from supplier which should be ready.

it will fit "most" pod, from what i know, HKS, K&N, blitz, apexi... enough? :cheers:

i don't have any normal top now, as i only sell 2 of them, 99% buyer wants clear top.

Josh: i never try to fit it to a R32, but we can work something out, PM me

fazt_r33: i can :P

  • 1 month later...

Hey i'm interested. What holds the box in place? Do i have to drill holes in my engine bay or what? Also has anyone else got this and noticed any power difference or got any dyno figures?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...