Jump to content
SAU Community

Recommended Posts

Steve was at the barbecue and Jeff was at the barbecue and I was at the barbecue; three men standing around a barbecue, sipping beer, staring at sausages, rolling them backwards and forwards, never leaving them alone.

We didn't know why we were at the barbecue; we were just drawn there like moths to a flame. The barbecue was a powerful gravitational force, a man-magnet. Jeff said the thin ones could use a turn, I said, "yeah I reckon the thin ones could use a turn", Steve said, "yeah they really need a turn"

- it was a unanimous turning decision.

Steve was the Tong-master, a true artist, he gave a couple of practice snaps of his long silver tongs, SNAP, SNAP, before moving in, prodding, teasing, and with an elegant flick of his wrist, rolling them onto their little backs. A lesser tong-man would've flicked too hard; the sausages would've gone full circle, back to where they started.

Nice, I remarked. The others nodded. Kevin was passing us, he heard the siren song sizzle of the snags, the barbecue was calling, beckoning, Kevinmmm ...come. He stuck his head in and said, "any room?" We nodded and began the barbecue shuffle; Steve shuffled to the left, Jeff shuffled to the left, I shuffled to the left, Kevin slipped in beside me, we sipped our beer. Now there were four of us staring at sausages, and Steve gave me the nod, my cue. I was second-in-command, and I had to take the raw sausages out of the plastic bag and lay them on the barbecue; not too close together, not too far apart, curl them into each other's bodies like lovers -fat ones, thin ones, herbed and continental.

Gary came along, he said, "looking good, looking good" -the irresistible lure of the barbecue had pulled him in too. We nodded and did the BBQ shuffle, left, left, left, left, he slipped in beside Kevin, we sipped our beer.

Five men, lots of sausages. Jeff was the Fork-pronger; he had the fork that pronged the tough hides of the Bavarian bratwursts and he showed lots of promise. Stabbing away eagerly, leaving perfect little vampire holes up and down the casing. Gary was shaking his head, he said, "I reckon they cook better if you don't poke them". There was a long silence, you could have heard a chipolata drop; this newcomer was a rabble-rouser, bringing in his crazy ideas from outside. He didn't understand the hierarchy; first the Tong-master, then the sausage-layer, then the Fork-pronger -and everyone below was just a watcher. Maybe eventually they'll move up the ladder, but for now - don't rock the Weber.

Steve handed me his tongs. I looked at him and he nodded. I knew what was happening, I'd waited a long time for this moment - the abdication.

The tongs weighed heavy in my hands, firm in my grip - was I ready for the responsibility? I snapped them twice, before moving in, prodding, teasing, and with an elegant flick of my wrist, rolling them back onto their little bellies. I was a natural, I was the TONG-MASTER.

... Until Steve got back from the toilet....

Link to comment
https://www.sau.com.au/forums/topic/58573-vic-bbq-heirachy/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
    • Correct. Um. I dunno. I haven't cared enough about the way that the NA cars work to know for sure. But..... The 33/34 turbo manual cars have an electronic speed sensor in the gearbox that outputs a +/- (ie, sawtooth AC) voltage signal. That is connected to the speedo. The speedo then outputs a 0-5v square wave (ie, PWM) signal that the ECU (and any other CU on the bus) sees. The speed sensor is NOT directly connected to the ECU. So here's the problem. Your new ECU expects to see the PWM signal, but must somehow be getting a direct signal from the diff speed sensor. Which would suggest that the wiring of the NA car is not the same as the turbo cars. I think you will need to spend some time with (hopefully the wiring diagram for the car) and a multimeter to see what is connected to what. Then, presuming I am correct**, you would then want to separate the ECU speed signal input from the rest of the car's wiring, and probably either buy a speed signal converter, or build one using an arduino (or similar). That would take in the speed sensor signal and output a scaled (and suitably rearranged) signal for the ECU. ** We shouldn't presume that I am correct here, because there might be something else crazy going on. I don't think you could convert the speedo to be fed from the gearbox sensor, because the pulse rate from that sensor is probably different to the diff sensor and then the speedo would read wrongly. And this also wouldn't fix the ECU's problem either, because the ECU doesn't want to see the gearbox signal direct either (assuming that they are all on the same wiring, for some odd NA related reason, see above caveat!) Does this help? Probably not. Can you make it work? Almost certainly. With the above work. You should buy a handheld oscilloscope from Aliexpress so that you can view these signals directly. Connect up the probes and drive the car. Show photos of the screen when drving at known speeds and connected to different places, and we'll see what we can learn about it.
    • Assuming your brake pads are not worn right down, I'd add a little brake fluid. Is there any sign of a brake fluid leak?
    • Hello all,  I need of some help. On my drive home my handbrake light lit up and started flashing. When I got home I checked my handbrake sensor under the centre console and nothing seemed out of the ordinary. I have scanned my car via the consult port, no codes shown. Checked my brake fluid as well which is half full. Tried unplugging the brake master but it didn't change anything. Thoughts on what it could be? The master float doesn't seem to be stuck. My car is an 1998 ER34 sedan GT. No hicas but has ABS Photos below 👇🏾 
×
×
  • Create New...