Jump to content
SAU Community

Recommended Posts

hey jason, I have one of geoff's bars on order, and will need it fitted (no tools here in sydney :rofl: ) so does your $120 include the allignment?

on a side note, I got home tonight with my GTR blowing a lot of smoke as I pulled in the garage! the engine is only 1500km old, with 3 oil changes under its belt! and the turbos are new at the time also...... oh and low boost too! only .9 bar !!!

Im off to ring the builder in the morning, but I am seriously hoping it is something minor or there will be tears!

maybe a blocked PCV? :S:S:S

cheers, and thanks to geoff for taking the time to make these for us guys!!!

white smoke....

spoke to morgs and to SK today.... they think it is oil breathing into the intake pipes, and I have checked the pipes... yep laced with oil!

so I need a catch can!!! and now to clean the intercooler and associated piping ...

gcg catch tank??

Just to clarify some of the questions about R32 GTR....

To remove HICAS altogether.....buy one of Geoff's bars, and either....a new power steering pump with 1 output, or a bolt the right size to replace the rear line outlet.

Disconnect the 2 ball joints at the hubs, and then remove the 2 bolts holding the HICAS bar to the subframe. Be amazed at how heavy it is.

Disconnect the 2 lines from the chassis that go to the HICAS bar, there are a couple of brackets holding the lines to the subframe.

Disconnect the 2 lines right to the front of the car, right up at the HICAS solenoids next to the plenum.

Remove both inlet and outlet lines from the HICAS solenoid (these lines run back to the power steering pump and power steer reservoir. Unlpug the wires and remove the bracket. Enjoy how much easier it is to remove your oil filter.

Remove the rear line from the power steering pump, unbolt the brackets and cut the metal pipe as it links around the power steering lines underneath (unless the engine is out in which case it just lifts out :rofl:)

Remove the line that run from the HICAS solenoid to the cooler to the reservoir. Remove the whole cooler and all its brackets. Remove the other line that runs from the solenoid to the pipe you just cut.

Put a nice big bolt in a short piece of line to block the empty exit from the reservoir.

Clean up the power steering fluid that is all over your garage floor.

Like anything, double check to make sure you have the right pipes, esp before you start cutting! There will be only 2 power steer lines left in the engine bay, it will go from one of the reservoir outlets to the front of the power steer pump, around the engine bay to the steering rack, then back around the back of the engine bay and back to the reservoir.

Just to clarify some of the questions about R32 GTR....

To remove HICAS altogether.....buy one of Geoff's bars, and either....a new power steering pump with 1 output, or a bolt the right size to replace the rear line outlet.

Disconnect the 2 ball joints at the hubs, and then remove the 2 bolts holding the HICAS bar to the subframe.  Be amazed at how heavy it is.

Disconnect the 2 lines from the chassis that go to the HICAS bar, there are a couple of brackets holding the lines to the subframe.

Disconnect the 2 lines right to the front of the car, right up at the HICAS solenoids next to the plenum.

Remove both inlet and outlet lines from the HICAS solenoid (these lines run back to the power steering pump and power steer reservoir.  Unlpug the wires and remove the bracket.  Enjoy how much easier it is to remove your oil filter.

Remove the rear line from the power steering pump, unbolt the brackets and cut the metal pipe as it links around the power steering lines underneath (unless the engine is out in which case it just lifts out ;))

Remove the line that run from the HICAS solenoid to the cooler to the reservoir.  Remove the whole cooler and all its brackets.  Remove the other line that runs from the solenoid to the pipe you just cut.

Put a nice big bolt in a short piece of line to block the empty exit from the reservoir.

Clean up the power steering fluid that is all over your garage floor.

Like anything, double check to make sure you have the right pipes, esp before you start cutting!  There will be only 2 power steer lines left in the engine bay, it will go from one of the reservoir outlets to the front of the power steer pump, around the engine bay to the steering rack, then back around the back of the engine bay and back to the reservoir.

That's great, I think that's what I've been searching for. I have a R32 GTST. Is this a similar setup to the GTR? Also, can I use the original pump, or what is an alternative pump to use? To clarify, can I remove eveything bar what goes from the reservoir to the pump, to the rack and back to the reservoir? I have a couple of metal plugs to go with the 2 spacers and 2 domed nuts from the locking bar kit. Where do I use them?

Thanks

Mitch :P

Hi Duncan,

Have you gone through this process and have it running in your car? Is all OK without the extra line (that used to go to the HICAS solenoid) and without the cooler?

In my mind the extra line may have relieved pressure in the system - though I would prefer to listen to your advice as someone who has gone through the exercise!

Yes we;ve made the changes above and given the car a *very* thorough work out since. No problems with the car or power steering.

Our main concern was whether the pump will last with 1 outlet just blocked off...dunno...if it dies we will be replacing it with a 1 outlet pump like an r33.

I'm not sure if a 32 gtst is the same but I suspect it is

Is the R33 pump a direct replacement?

Which is the Hicas outlet on the R32 pump?

Thanks again

Mitch:)

I'm not sure but apparently so,

And the HICAS outlet is the rear one on the Power Steering pump. But for goodness sake before you start pulling it out...double check everything!

  • 2 weeks later...

Right, blocked the rear outlet from the pump, and also the return to the reservoir.

Haven't yet swapped out the Hicas rack, but there is Power Steering fluid pissing all over from somewhere or other. I thought it was from the main return to the reservoir, so replaced it with a braided hose, but after taking it for a run out, there's an explosion of fluid all under the engine, hoses, suspension-everywhere.

Is there a possibility that the rear outlet being blocked is causing excess pressure in the system?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • 2001 BE5D Subaru Legacy B4 RSK (3rd gen) EJ208 (pink injector) Twin Turbo 280PS 5-speed manual Full time 4WD "RSK" grade which means all of the above LQC option which means stock rear spoiler  I got it primarily to export to someone outside Japan who was interested. These BE5 Legacy B4 RSKs are going through a bit of a resurgence right know in Japan as they are one of the few cars from the "turbo, manual, RWD/4WD, 280hp gentleman's agreement era" cars that don't require stupid money to purchase. Which for some people might be a good opportunity to get as a base for restoration. If I can't find anyone to purchase it I will certainly be doing that myself over the long term. Why? Because it's properly fast in stock form, handles well enough for a GT sedan, there's still enough aftermarket and (if you can wait a while) genuine part support to make it a restoration candidate (<-- that will only get worse over time so it's a case of do it now or choose get a BL5 4th Gen). Mechanically it's fine, has only 89,200kms on the odometer. The problem with this car is that the body and exterior trims are weathered from at least the last 10 years being parked outdoors. I'm the 3rd owner, the first owner was the one that had it for 14 years and barely drove it, had a low-speed front impact (which didn't damage anything behind the radiator support) and got it fixed and sold it. The 2nd owner put most of the kms on it and parked it outside for the last 10 years, hence the door rubbers have seen better days but if you overlook those cosmetic details, it presents pretty nicely. There is some minor rust on the LH rear wheel arch which I'll have looked at too at some stage.  Also as you'd expect from a car this age, the clear top coat is gone, leaving a satin finish on the roof.  Mechanically it's fine (as you would expect from a car with less than 100K kms) but the steering does feel slightly vague around the centre position at higher speeds. So first on the list is to get the steering rack bushes looked at. There's also the Lock button on the remote which doesn't work, but the Open button does.... it means that the anti-theft system thinks it's always open? It seems like if you open the car and don't start the engine within 3 mins or so the anti-theft kicks in again without any beeps or signals. So if you got to start it after that, it won't. You have to push the open button again. That's how I understand it anyway. Just a small irritation but not a big problem to sort out. There's only one mod, the Wangan SPL muffler. Just a tad louder than stock. It's a really good mod for those who don't want to wake the neighbours but still want to hear a more prominent unequal length header EJ20 sound. Anyway I hope to get all those things done eventually, that is unless someone wanted to import it to their country from Japan (where I live). I'm open for negotiations as I really would like a Skyline... but this will definitely suffice in the meantime 🙂 *Disclaimer: This is how I picked it up from the dealer, minus the stuff on the back seat. I haven't cleaned the engine bay or done a thorough exterior clean, aside from spray painting the wipers. 
    • Wow, even with the Audi logo centre caps. I love OEM wheel mismatches. 
    • Welcome!  Can't go wrong with a Stag.
    • Looks good. Nice height.
    • Hey all, a little help from the Stagea hive mind plz.. I'm days away from buying either a 2002 Stagea 250tRS AR-X Four, premium leather, power seats and all the old switches etc that go with it, or a 2002 Stagea 250tRS VR-X Four AERO, pov pack, cloth seats etc, with coil overs, sports zorst, comes with original zorst and suspension and parts. (I think I've got the models right?) Both are VQ25DET, have 160000kms, both straight no rust both with $2000+ in recent servicing receipts, both ride on aftermarket 18" rims. The Aero has a replaced turbo as well. I like the cool factor of the Aero car but the AR-X has never been modified. Neither have been driven hardly at all in the last 5 years. Any thoughts on which one or does it come down to personal preference? davemoto 
×
×
  • Create New...